background image

Page 24 

ENGLISH

  

 

Zodiac

®

 JXi

 Gas-Fired Pool & Spa Heater   

|

   Installation & Operation Manual

Section 7.  Optional Remote Controls

The JXi heater controls can be wired for remote 
operation. All Zodiac

®

 AquaLink

®

 Control Systems will 

permit the heater to be operated by remote control. The 
instructions in the following sections should be used as a 
general guideline only. Please follow the instructions that 
accompany your selected control system thoroughly.

Electrical wiring must be in accordance with the latest 
edition of the 

Australian Wiring Rules (AS/NZS 3000) 

and all other applicable installation codes.

Refer to 

Figure 12 

for a complete diagram of wiring 

connections and terminals.

7.1 

Connecting to a Remote Pool-Off-Spa Selector (3-Wire Connection)

• 

Turn off the power to both the pool/spa control 

system and the heater unit.

• 

Remove the front panel.

• 

Run the wires from the pool/spa control system 

through the low voltage knockout on the right or left 
hand side of the heater.

• 

Connect the wiring from the pool/spa control system 

to the heater remote control terminal. See 

Figure 12 

item “b”.

• 

Connect the three wires to Spa, Pool & Common 

terminals of the J6 terminal bar.

• 

Reinstall front panel.

• 

Restore power to the heater and the pool/spa control 

system.

7.1.1 

Configure the Control Panel:

•  Make sure the pool heater is OFF.
•  Press and hold MENU, then the POOL and SPA 

buttons for 5 seconds to access Service Setup mode.

• 

Press Up or Down to display REMOTE.

•  Press MENU, 

REMOTE OFF

 (default remote) is 

displayed.

• 

Use Up or Down to scroll through the Remote options 

until 

HI-LO-COM

 is displayed, then press 

MENU

 to 

select.

•  Press 

POOL

 or 

SPA

 to exit Service Setup mode.

NOTE: 

The display will revert back to OFF after 1 minute since the 

last key press.

7.2 

Connecting to a Remote TSTAT (2-Wire Connection)

An interrupt (on/off-type) remote can be connected as a 

Remote TSTAT to turn the heater on or off but not 

perform any other function. When using this type of 

connection, remember to set the heater control to “SPA” 

and set the thermostat control to maximum.

7.2.1 

Install the Remote TSTAT:

• 

Turn off the power to both the pool/spa control 

system and the heater unit.

• 

Remove the front panel.

• 

Run the wires from the pool/spa control system 

through the low voltage knockout on the right or left 
hand side of the heater.

• 

Connect the wiring from the pool/spa control system 

to the heater remote control terminal.

•  Connect the two wires to Pool and Common (not 

Spa) on the J6 terminal bar. See 

Figure 12 

item “b”.

• 

Reinstall panel.

• 

Restore power to the heater and the pool/spa control 

system.

NOTE: 

If you install a time clock to control the filter pump 

operation, it is recommended that the time clock have its own low 
voltage (Fireman’s) switch to turn off the heater before turning off 
the pump. The switch should shut off the heater about 15 minutes 

before the filter pump shuts off. This will allow for a more efficient 

operation by removing any residual heat contained in the heat 
exchanger back to the pool.

CAUTION

To avoid damage to the heater, 

do not

 

connect the power supply 

of the heater to the output side of the clock 

if your time clock 

simply interrupts the high voltage power supply or has a high voltage 
output. Doing so will prevent the blower from purging the residual 
heat from the heater when the heater turns off. The blower must be 
allowed to run for 45 seconds after the heater shuts off.

7.2.2 

Configure the Control Panel:

•  Make sure the pool heater is OFF.
•  Press and hold MENU, then the POOL and SPA 

buttons for 5 seconds to access Service Setup mode.

NOTE: 

The display will revert back to OFF after 1 minute since the 

last key press.

•  Press MENU, 

REMOTE OFF

 (default remote) is 

displayed. 

• 

Use Up or Down to scroll through the Remote options 

until 

REMOTE TSTAT

 is displayed, then press MENU to 

select.

• 

Press POOL or SPA to exit Service Setup mode.

• 

Press SPA to adjust the set point to the maximum 

40°C.

Содержание JXi 200













































Отзывы: