background image

19

EE02

Low pressure protection

Low-pressure sensor broken.

 Replace the low-pressure sensor.

Insufficient level of refrigerant.

 Add refrigerant.

Ambient temperature and input 

water temperature too low.

Send the pump to the retailer for a 

detailed inspection.

EE03

Water flow rate protection

Flow switch incorrectly positioned.

 Re-make the connections.

Insufficient water flow.

Increase the water flow rate.

Broken flow switch.

 Replace the flow switch.

Faulty filter pump.

Repair or replace the filter pump.

EE04

In heating mode, temperature 

overheating error 

In heating mode, temperature 

overheating error.

Check that the flow rate is sufficient.

Faulty flow switch.

 

Replace the flow switch.

Abnormal d2-TH5 sensor reading.

 

Replace the d2-TH5 sensor.

EE05

d6-TH3 exhaust temperature protection

Insufficient refrigerant.

 Check for the presence of gas 

leaks and add refrigerant.

Insufficient water flow rate.

Check the by-pass valve.

Clogged filter or electronic valve.

 

Check refrigerant levels.

d6-TH3 sensor fault.

 

Check the d6-TH3 sensor.

EE06

Controller fault

The connection is faulty.

 Check the connection.
 Replace the cable.

The controller is faulty.

 Replace the controller.

EE07

Compressor protection

The connection is faulty.

 Check the connection.

Accumulation of liquid and gas.

 Check the power supply voltages

Faulty compressor or printed circuit 

board.

 Check the phases.

Abnormal water flow rate.

 Check the water flow rate.

Fluctuating power supply.

Check the electrical grid.

EE08

Communication error between the 

controller and the power board

The connection is faulty.

 Check the connection.
 Replace the cable.

The controller is faulty.

 Replace the controller.

EE09

Communication error between the 

controller and the control board.

The connection is faulty.

 Check the connection.
 Replace the cable.

The controller is faulty.

 Replace the controller.

EE10

High voltage protection

Voltage too high.

 

Check the voltage.

Faulty power board.

 

Replace the power board and/or 

control board.

Содержание HPO





























Отзывы: