background image

 

13 

2.6 Configure Alarm 

Note: If an alarm is triggered, the device generates an alarm. 30 seconds later, 

the alarm is switched to an alert. The alarm can be terminated after the user is 
authenticated. 

 

Configure Alarm setting 

The  alarm  should  be  on  by  default,  when  it  is  set  to  be  close,  the  Error 
Operation-Triggered Alarm, Tamper Alarm, the Alarm Delay for the Door Status 
Sensor will be disabled. 

1. The administrator 
password is authenticated. 

2. Press

(The indicator turns green 
and makes a long beep.)

3.

Press 1. 

(The indicator turns green 
and makes a long beep.)

5. The configuration is 
successful.
(The indicator turns green 
and makes a long beep, 
then turns red and makes a 

long beep again.)

.Configure the  alarm 

setting.
 (0: enable; 1: disable).

6.Exit. 
(The device automatically 
exits the process when the 
operation is completed.)

 

Note:  The  indicator  turns  red  and  makes  a  long  beep  in  fifth  step  indicates 

system exits when setting successfully.

 

 

Configure Error Operation-Triggered Alarm 

If  this  function  is  enabled,  alarms  are  generated  if  an  administrator  fails  the 
authentication  upon  three  attempts.  The  administrator  authentication  is  not 
allowed within 20 seconds after an alarm is generated. 

1. The administrator 
password is authenticated. 

2. Press

(The indicator turns green 
and makes a long beep.)

3.

Press 2. 

(The indicator turns green 
and makes a long beep.)

5. The configuration is 
successful.
(The indicator turns green 
and makes a long beep, 
then turns red and makes a 
long beep again.)

.Configure the error 

operation-triggered alarm 
switch.
(0: enable; 1: disable).

6.Exit. 
(The device automatically 
exits the process when the 
operation is completed.)

 

Note:  The  indicator  turns  red  and  makes  a  long  beep  in  fifth  step  indicates 

Поставщик систем безопасности: TELECAMERA.RU

Содержание X7

















Отзывы: