background image

 

11 

2. The indicator turns red and makes a long beep in fourth step indicates system 
exits when setting successfully.   

2.3 Configure Authentication Mode 

1. The administrator 
password is authenticated. 

2. Press5. 
(The indicator turns green 
and makes a long beep.)

3. Enter the authentication 
mode.

5.Exit. 
(The device automatically 
exits the process when the 
operation is completed.)

4.The configuration is 
successful.
(The indicator turns green 
and makes a long beep, 
then turns red and makes a 

long beep again.)

 

Note: 1.The indicator turns red and makes a long beep in fourth step indicates 

system exits when setting successfully. 

2. Details about the authentication mode are as follows: 

Authentication Mode 

type

 

Description

 

Mode 1 (number1) 

PW 

Only password verification   

Mode 2 (number2) 

RF 

Only RF Card verification 

Mode 3 (number3) 

FP 

Only fingerprint verification 

Mode 4 (number4) 

FP/PW/RF 

fingerprint or password or RF verification 

Mode 5 (number5) 

RF&PW 

RF and password verification 

Mode 6 (number6) 

FP&PW 

fingerprint and password verification   

 

2.4 Configure Concealed Mode 

If the Concealed mode is enabled, the indicator is off when the Concealed mode 
is in the sleep mode. 

Поставщик систем безопасности: TELECAMERA.RU

Содержание X7

















Отзывы: