background image

 

TS1200: 

  Tripod Turnstile 

TS1211:

  Tripod Turnstile with Controller and RFID Reader 

TS1222: 

  Tripod Turnstile with Controller and Fingerprint Reader with RFID function. 

Please read this document carefully before installation and using the device. 

1. Technical Specifications 

Input Voltage 

AC 100~120V /200~240V,   

50Hz /60Hz 

Max. Tolerance of Arms 

Center: 80 kg 

End: 40 kg 

Rated Power 

60 W 

Ingress Protection Degree 

IP54 

Operating Environment  Indoor and Outdoor (shelter) 

Arm Length (mm) 

520 

Operating Temperature 

-28ºC ~ 60ºC 

Net Weight 

55kg 

Operating Humidity 

5% ~ 85% 

Gross Weight 

63kg 

Flow Rate 

25~30 passages / minute 

Dimension(mm) Figure 1  L = 600, W = 330, H = 990 

Input Control Signal 

Dry contact 

Package Size (mm) 

L = 730, W = 450, H = 1080 

 

Figure 1

 

 

2. Arm Installation and Equipment Testing 

 

2.1 Arm installation method 

Installation procedure 

1. Using the glue and applying in the hole of the arms as 

well as the one screw, as shown in Figure 2-1. (This is to 
prevent screws from getting loose due to vibration 
after being used for a long time.) 

 

 

 
 
 

 

 

 

 

Figure 2-1 

 

This hole shall be 

applied with glue 

evenly. 

Содержание TS1200 Series














Отзывы: