background image

 

 

Figure 3-1 

Notes:   

1. The space at the end of the arm shall not be greater than 80 mm (see Figure 3-1). 

2. Setting a warning line for card swiping (see Figure 3-2). A warning line is suggested to prompt users to swipe cards in a 

distance, which would greatly reduce the probability of equipment failure caused by improper operations. 

 

 

Figure 3-2 

3.2 Cabling 

There are inlets in the bottom plate for cabling, as shown in Figure 3-3, the unit is millimeter. Power supply and 
communication wire should go through the inlet. Cable protection covers are suggested to use if it is surface mounted. 

Warning

: The tripod turnstile must be connected to the ground (earth), there is wiring interface near the power switch. 

 

Figure 3-3 

3.3 Installation 

1.

Drilling holes. 

Drill holes based on the locations of the holes shown in Figure 3-3.

 

2.

Fix the mounting plate to its original position. 

Assistant 

framework

Warning line for card swiping

Warning line 

for card swiping

Warning line for card swiping

Warning line for card swiping

Warning line 

for card swiping

Warning line for 

card swiping

Содержание TS1200 Series














Отзывы: