background image

BG500 Series Barrier Gate

User Manual

P a g e

|

21

Copyright©2022 ZKTECO CO., LTD. All rights reserved.

9

Boom Barrier Adjustments

Horizontal and Vertical Angle Adjustment of Barrier Boom

(Mechanical Adjustment)

Note:

The horizontal and vertical angles of the barrier boom have been adjusted before

leaving the factory. Please do not adjust them without the guidance of professionals to
avoid any mechanical damage.

1.

Adjust the horizontal position of the barrier boom

The connecting boom crank will be an overlapping structure, and the two rotation
points of the connecting boom are coincident with the output shaft of the reducer at 3
points and a line. This is the horizontal position of the barrier boom. If you find that the
barrier boom is not in level or inclined at this time, then loosen the 2 screws of the
spindle connecting arm, turn the barrier boom to the level, and then tighten the screws.

2.

Adjust the vertical position of the barrier boom (adjusted by mechanical structure)

The connecting boom crank is in an unfolded shape, and the two rotation points of the
connecting boom and the output shaft of the reducer are in an unfolded 3-point line.
This is the vertical position of the barrier boom. If it is found that the barrier boom is not
in the vertical position and is inclined at this time, then loosen the 2 screws of the rocker
(rocker-arm), then turn the barrier boom to the vertical, and tighten the screws.

Содержание BG500 Series




























Отзывы: