Magnetic Lock User Manual
Wiring:
The positive phase and negative phase are connected to the power box. Use the model that has signal output.
Signals are connected as required by users:
1.Connected to COM and NO if normal open signals are necessary;
2.Connected to COM and NC if normal close signals are necessary;
3.The indicator lamp turns red if the lock is separated from the adsorption plate or if contact is not thorough. The lamp
will turn green if the lock and the adsorption plate contact with each other correctly.
4.In case of abnormal indicator lamp when the lock is working, it may be caused by improper contact between the lock
and the adsorption plate. Adjust the position of the lock and the adsorption plate to ensure thorough contact.
Precautions:
1. Cables shall be larger than 0.75mm2 in case of power supply with a large power capacity (the output of power supply controlled within 12VDC
±
15% strictly).
2. The screw connecting locks and
Armature plate
shall be tightened. Check the fixing of the lock and the board after three months.
3. Install carefully to avoid damage to
Armature plate
and the galvanized coating of locks, and otherwise, the normal use, suction force and service life will
be damaged.
4. The complete contact between the
Armature plate
and the lock as well as the size of contact surface will decide the suction force directly.
5. A rubber ring is required between the
Armature plate
and the lock so as to maintain a proper flexibility of the suck board, and tensive screws of the
Armature plate
shall not be fixed too tightly in order to maintain the appropriate flexibility of rubber ring.
6.
Armature plate
cannot be welded on the door directly, and otherwise, the normal use of magnetic locks will be damaged.
7. Wipe off rust-preventive oils on the locks with cotton cloth while alkaline or irritant detergents not allowed.
Armature plate
NC
GND
NO
PUSH
12V
GND
GND
12V
-
+
UPS
Control
NC NO
COM
-
+
A L - 1 8 0
A L - 1 8 0 D
A L - 2 8 0 ( L E D )
A L - 2 8 0 D ( L E D )
3 3 2 X 2 1 X 4 0
1 6 6 X 2 1 X 4 0
2 5 3 X 2 5 X 4 8
5 0 6 X 2 5 X 4 8
380
760
500/250
1000/500
500/250
700/350
1000/500
2 5 3 X 2 8 X 5 5
5 0 6 X 2 8 X 5 5
2 8 0 X 3 8.5 X 7 0
A L - 3 5 0 ( L E D )
A L - 3 5 0 D ( L E D )
A L - 5 0 0 ( L E D )
2 4 V 1 0 %
A L - 1 8 0 M
1 9 8 X 2 1 X 3 5
380
1 2 V 1 0 %
Model
Dimensions (mm)
Vol tage
(DC )
Curr ent
(mA)
Indicator Lamp & Signal
Output (NC/NO)
AL-350(LED)
10.During installation of this product, offset (toward right, left, upside and downside) of center position of both the adsorption plate
and the lock shall not exceed 3mm.
Door frame not
less than 5mm.
Y
X
O
Series
Thickness
（
A1
）
Thickness
（
A2
）
Direction
Left
Right
Up
Down
X(mm)
Y(mm)
Door Frame
Door Frame
AP-180
AP-280
AP-350
AP-500
>38
>48
>43
>53
>46
>56
>58
>68
≤
3
≤
3
≤
3
≤
3
0
0
0
0
(mm)
(mm)
1 2 V 1 0 %
Wood
Door
Pull out
Electric Strike Series
Magnetic Lock Series
El ect ric Bolt Lock ser ies
Brackets and Accessories
Me cha ni cal Lo ck Se riess
El ec tron ic Lo ck Se ries
Electric Strike Series
Magnetic Lock Series
El ect ric Bolt Lock ser ies
Brackets and Accessories
Me cha ni cal Lo ck Se riess
El ec tron ic Lo ck Se ries
Wel co me to us e Adv an ced Lo ck prod uc ts. In order to protect yo ur righ ts an d inter ests, read thi s User Man ua l caref ul ly be fore us e. Please
co ntact the de al er or the man ufact urer in case of qu ery .
ELECTRIC LOCKS
Applicable Range:
This lock is applicable for use together with building interphone and access control system. This lock is applied extensively in
security door, emergency door and fire door.
Product Advantage:
The magnetic lock adopts professional magnetic materials and special processing workmanship. No residual magnetism is
produced even after long time operation. Long-time use will not cause magnetization of adsorption plate and result in reduction
of adsorptive force. This lock has longer service life and is free of mechanical failure, abrasion and noise.
Auxiliary bracket can be used for installation of frameless glass door.
o
Door Opening:
90
Electrical Property:
Users can select suitable products with different models and functions based on the following table. Customization is available
according to users' requirements.
Not provided
Not provided
Not provided
Provided
Provided
Provided
Provided
Provided
Access control
power source
Access
controller
Pull out
1400/700
560
X 3 8.5 X 7 0
A L - 5 0 0
D
( L E D )
Provided
(2000)量认(国)字(H0992)号
太平洋承保
质
