17
•
Operation on slippery or lumpy ground is
forbidden.
•
Operation is forbidden when the machine
is used otherwise than explained in this
operation manual.
For another usage and resulting damages
or injuries ZIPPER MASCHINEN doesn’t
assume any responsibility or guarantees.
2.5
Assembly
When the machine is conveyed, it has already
been assembled. Control the screws and pull
them behind if they are loose. The safety bolt
(Fig. D) must also be controlled about its fit-
ting.
2.6
Operation instructions
2.6.1
Start/Stop (Fig. C)
By pushing the green button 16, the machine
starts. When you push the red button 17 the
machine stops.
Important: Let the machine come to its max-
imum speed before beginning to work.
2.6.2
Workings before starting-up
•
Control the running direction of the saw
blade by turning on the machine shortly.
Right running direction: see the arrow on
the saw blade cover (Fig. E)
When the running direction is set false,
the machine has to be stopped immedi-
ately – danger of injury by loosing of the
blade. Then turn the phase inverter 15
180° around (Fig. D).
•
Make sure that the saw blade is fitted
tightly, is sharpened, is in a proper status
and guarantees a good run.
•
Before starting-up make sure that the
compensator is extracted. Otherwise
there’s a high risk of kickback.
•
Take care of foreign bodies like nails- and
of any anomalies in the work piece like
knurls.
•
Control whether the moving parts work
faultless and don’t get jammed.
2.6.3
Operation
•
Put the log on the log table (the compen-
sator must be extracted completely).
•
Turn on the machine.
•
Grasp the handle of the compensator with
both hands.
•
Then you have to move the compensator
forwards carefully.
•
The work piece is protected from turning
by the hooks 19 (Fig. G).
•
After cutting you have to extract the com-
pensator again.
•
If necessary put the next work piece on
the log table. It must be laid on the table
from the left side. Do the steps 3, 4 and 5
again.
•
After working you have to stop the ma-
chine.
•
Wait till the machine stands still again.
2.7
Maintenance
A T T E N T I O N
No cleaning, upkeep, checks or
maintenance when machine is run-
ning
Be safe: Shut off the machine, let it cool
down, disconnect spark plug cap from
spark plug.
The machine does not require intense mainten-
ance. However, to ensure a long lifespan, we
strongly recommend following the upkeep and
maintenance plan.
Repairs must be carried out by specialists! Use
original ZIPPER parts only!
2.7.1
Changing the saw blade (Fig. H to
Fig. N)
•
Remove the screw 20 from the cover
plate 21 and move it downwards (Fig. H).
•
Remove the split pin 22 and washer from
the rear end of the safety bolt with the re-
turn spring 10 (Fig. I).
•
Put the feed carriage downwards and
place it on the floor (Fig. J).
•
Place the lock bolt 24 into the hole 34 in
the fixed saw blade cover 2 and fix the
saw blade 4 (Fig. K). The lock bolt must
be visible on the other side.
•
Loosen the screw 26 with the included
tool 33 and remove the plate 25 (Fig. L).
•
Now change the saw blades. Take care of
the running direction! Before fitting the
disassembled parts they must be cleaned
carefully!
Содержание ZI-WP700J
