ZIEHL-ABEGG ZAtop SM180.24/B Скачать руководство пользователя

Страница: 24 / 76

6.5.4

Automatic emergency evacuation

The automatic emergency evacuation is described in the operation instructions of the control, the

frequency inverter and, if available, an evacuation unit with UPS.

7 Faults and remedy

Excessive temperature / Temperature protection trips

Fault

Causes

Adjustment

Noises on elevator

machine

Bearing defective

Contact customer service

Wrong setting at the frequency inverter

Check setting at the frequency inverter

Absolute encoder defective

Change absolute encoder

Excessive tempera-

ture / Temperature

protection trips

Surface of the elevator machine is covered Remove cover from drive or mount with

more distance to the elevator machine.

Ambient temperature higher than 40

Enhance shaft ventilation

Wrong setting at the frequency inverter

Check setting at the frequency inverter

Elevator machine

does not start

Motor phases connected incorrect

Check motor connection

VVVF defective

Check VVVF

Brake does not release

See brake faults

Elevator machine

does not turn when

the brake is released

Brake rotor sticks after a long storage time

on the armature disk

Release the brake mechanicaly or remove it

and loosen the brake rotor carefully from the

armature plate.

Brake switching

noises

Brake is switched on the DC-side

Modify the control to AC switching for nor-

mal operation. Fit an additional protective

circuit.

Air gap of brake too big

Replace the brake rotors (Special tool re-

quired! Contact the customer service of

ZIEHL-ABEGG SE).

Brake does not re-

lease

Power supply too low. The voltage at the

brake is to low.

Check supply, if necessary increase cable

cross-section (and transformer)

Brake control wrong / defective

Check brake control

Brake coil defective

Replace brake (special tool required.

ZIEHL-ABEGG SE Contact customer serv-

ice).

Brake worn out

Replace the brake rotors (Special tool re-

quired! Contact the customer service of

ZIEHL-ABEGG SE).

Brake release moni-

toring does not

switch

Microswitch/inductive proximity switch de-

fective

Replace microswitch/inductive proximity

switch

Contacts dirty

Operate microswitch/inductive proximity

switch with a higher contact current, at least

10 mA or replace microswitch/inductive

proximity switch or brake

Table 7

8 Service and maintenance

8.1

General notes on maintenance

Observe the safety-at-work regulations!

Disassembling the elevator machine can only be done with special devices!

Caution, strong magnetic force!

Never use a high-pressure cleaner (for example steam jet cleaner) for cleaning the elevator

machine!

Take note of abnormal operating noise.

Original operating instructions

ZAtop

–

model series SM180

Faults and remedy

A-TBA17_05-GB 2008 Index 003Part.-No. 01015765-GB (EU-BD 845/1 + 845/2)

24/76

Содержание ZAtop SM180.24/B













































































Результаты поиска

Содержание ZAtop SM180.24/B

Отзывы:

Похожие инструкции для ZAtop SM180.24/B

Бренды по названию

Популярные бренды

ZIEHL-ABEGG ZAtop SM180.24/B, Оригинальная инструкция по эксплуатации

Результаты поиска

Содержание ZAtop SM180.24/B

Отзывы:

Похожие инструкции для ZAtop SM180.24/B

Бренды по названию

Популярные бренды