background image

5

Visual inspection of nut 

tting

Requirement

Using the documentation provided on site and any adhesive labels attached to the gearbox, check 
whether one of the following measures has been completely and successfully carried out.

3 x Brief check of screw connection on worm gear in line with A-TIA19_04

2 x Torque check on screw connection on worm gear in line with A-TIA19_05

Repair of screw connection on worm gear in line with A-TIA 19_06

If this has not been done, 

rst complete the series of tests that has been started with the brief check or 

torque check.

Procedure

"

Disconnect the elevator system from the power supply using the main switch, secure it against 
being switched back on and check that there is no voltage.

"

Do not activate the manual hand release!

Inspection goal:
Identi

cation of loose nuts.

Inspection goal:
Visually check that all nuts are tightly 

tted on the worm gear.

If the visual check of the nut 

tting reveals a loose nut (as shown in the 

gure 

Incorrect nut 

tting

), 

contact ZIEHL-ABEGG SE. See back page for contact details.

Figure 4 - Incorrect nut 

tting

Attention!

If a nut 

tting is incorrect, shut down the system. Contact the ZIEHL-ABEGG SE customer service. 

See back page for contact details.

We recommend noting performance of the check and its results in the elevator documentation.

Service instructions 

ZAS0, ZAS1, ZAS2, ZAS3

Visual inspection of nut 

tting

A-TIA19_07-GB 1936 Index 001

Part.-No. 01013457-GB

11/12

Содержание ZAS Series













Отзывы: