ZIEHL-ABEGG Icontrol FXDM Series, Руководство по эксплуатации

Страница: 21 / 96

7 Base setup
7.1 Jumper for the input signal
Jumper position factory setting for 0 - 10 V signal. For temperature sensors (TF..) or sensors with 4 - 20 mA bring the
internal jumper for the external signal in the correct position. Caution- not under voltage! Observe the savety notices!
When using
“ other sensors ” bring the jumper in the correct position. The adjustment of the measuring range takes
place in the Base setup of respective Mode.
E1 Analog In (factory setting 0 - 10 V)
A
E1 GND
0-10 V
10 k
0 - 10 V TF..
24V E1
GND
DSG 0 - 10 V
YE
DSG..
(0 - 10 V)
WH BN
24V E1 GND
MAL 0 - 10 V
3
MAL1/10
(0 - 10 V)
2 1 3 1
BN GN
MBG..-I
24V E1
MBG..
(4 - 20 mA)
E1 GND
TF..
30.05.2012
v_stecker_e1.vsd
E1.2 E1.1
0 - 10 V
E1.2 E1.1
0 - 10 V
E1.2 E1.1
0 - 10 V
E1.2 E1.1
4 - 20 mA
(0 - 20 mA)
E1.2 E1.1
TF.. (KTY)
R
e
x
t
10 V PWM
f = 1...10 kHz
R
ext
> 10 x Ri
sig
GND E1 A
10 V
Ri
sig
E2 Analog In for modes with two
sensors
22.01.2008
v_stecker_e2.vsd
TF..
3 1
BN GN
MBG..-I
24V E2
MBG..
(4 - 20 mA)
E2 GND
TF..
E2.2 E2.1
4 - 20 mA
(0 - 20 mA)
E2.2 E2.1
TF.. (KTY)
7.1.1 External Setpoint / External speed setting in manual operation
External Setpoint or external manual operation is possible by 0-10 V (0-20 mA, 4-20 mA) Signal at terminals
“
E2
”
and
“
GND
”
.
Place internal Jumper
“
E2.1
”
and
“
E2.2
”
for
“
E2 Analog In
”
in correct position.
“
E2
”
Con
fi
guration in base setup. For
Potentiometer AnalogOut1 (terminal
“
A
”
) program to function
|
1A
|
=
“
+10 V
”
(like factory setting IO Setup). If a second
sensor is connected at input 2, external Setpoint or speed setting in manual operation is possible with additional modul
“
Z-
Modul-B
”
(input E3 IO Setup).
E2 Analog In = factory setting 0 - 10 V
A
E2 GND
0-10 V
Analog In 2
02.12.2009
v_extern_stecker_v.vsd
E2.2 E2.1
10 k
E2 Analog In = 0 - 20 mA / 4 -
20 mA
E2.2 E2.1
Analog In 2
24.01.2008
v_extern_stecker_a.vsd
External Setpoint via external signal instead of
“
Setpoint 1
”
. The
“
external Setpoint
”
function must be activated in base setup
|
1E
|
for
“
E2 function
”
. The active external Setpoint value is displayed in the
“
info
”
menu group.
External speed setting in manual operation. The
“
external manual operation
”
function must be activated in the basic settings
|
2E
|
for
“
E2 function
”
. Switchover between settings on the device and external manual operation via the digital input ( IO
Setup:
“
Control / manual operation
” |
7D
|
).
Operating Instructions Icontrol
–
model series FXDM Base setup
L-BAL-E036-GB 1422 Index 008 Part.-No. 00154773-GB
21/96