Zhermack Cyclope, Руководство пользователя

Страница: 10 / 16

20
cyclope The reference figures can be found on pages 3 and 4 of this manual.
EN
6.3 SPACE NECESSARY FOR USE
The choice of the place and space required for
installation is an important factor for the quality
of work and safety and for correct maintenance
activities. This area must not only be spacious
enough to allow for optimum equipment operation
- also during cleaning and maintenance phases -
but must also be well lit, aired, not dusty and not
exposed to direct sunlight.
6.3.1 WORkTOP
Fig. D: cyclope has been designed to work on a
rigid worktop and parallel to the ground. Suitable
worktops include service furniture (operator is
standing) or modelling tables (operator is sitting).
All worktops must be checked for stability.
Note also that the unit must be positioned so the
connection plug can be handled/manipulated with
ease.
6.4 CONNECTION TO ENERGY SOURCES
The connection is made using the power supply
cable. Check:
• that mains power supply voltage and
frequency correspond to those indicated on the
identification plate (an incorrect power supply
voltage may damage the equipment);
• that the power supply mains has a suitable earth
connection.
Do not tamper with the power supply cable
and relative plug. For replacement of the
same due to damage and/or wear, only
contact Authorised After-Sales Centres.
An earth connection is mandatory.
If an extension must be used
temporarily, it must be in
compliance with the standards in
force in the country of use.
6.5 INITIAL START UP
Fig. 1: Rest the appliance on a level work surface
with the induction chamber facing the operator.
Fig. 2: Insert the main power socket into the
appropriate outlet at the rear of the device and
subsequently connect the plug to the mains.
Follow the instructions given in paragraph 6.4.
meticulously.
Fig. 3: Before starting work, place the protective
cap (x) in the induction chamber. This collects drops
of wax and keeps the appliance clean.
Fig. 4: Turn the appliance on by pressing the ON/
OFF switch (fig. A, 3). The appliance is now in stand-
by. This is indicated by the green light on the front
panel.
Failure to comply with any of the above-
stated equipment installation regulations
can lead to equipment malfunctioning and
render the warranty null and void.
6.6 DECLARED USE
The cyclope is designed to heat metal spatulas and
similar instrument used to model objects made
from dental wax.
6.7 NON-DECLARED/PROhIBITED USE
Using the equipment for any purpose not
considered in paragraph regarding
“Declared use” shall be considered improper
and thus forbidden.
The improper use of the equipment renders
the warranty null and void and Zhermack Spa
declines all liability for any damage to objects
and injury to operators or third parties.
The main reasons for which the warranty is rendered
null and void are given in paragraph 2.2 and in the
“Warranty Certificate” attached to this Manual.
CHAPTER 7: USING THE EqUIPMENT
7.1 GENERAL WARNINGS
The tool heater must not be used near
pacemaker wearers.
For total certainty of safe operation,
scrupulously follow the work phases given
below.
• Do not place fingers with metal rings in
the induction chamber; risk of burns.
• Do not leave metal objects in the
induction chamber for too long or they
may become incandescent.
• To avoid the occurrence of any risks, pay
attention to avoid pouring water during
the preparation on the electrical voltage
parts.
• To avoid damage to the appliance:
- Do not place metal objects near the coil,
this could jeopardise correct operation
of the tool heater.
- Heating occurs only when metal objects
are placed in the chamber. Do not insert
other materials.
- keep the outside frame of the appliance
free from molten wax.
7.2 USING ThE TOOL hEATER
Once it has been correctly installed and put into
service, proceed as follows:
Fig. 5: Heat the spatula (y) by placing it at the
centre of the induction chamber, making sure it
does not touch the inside wall.
Induction is activated by the position sensors which
detect the presence of the instrument. The red and
green LEDs light up alternately.