Zetor MAJOR HS Series Скачать руководство пользователя страница 94

Страница: 94 / 140

Basic service information

Accumulator battery must be always connected by a 'minus' pole to earth electrode and 'plus' pole connected
with alternator. Reversely connected accumulator battery will destroy the whole of semiconductor device of

alternator. When using auxiliary accumulator battery for starting the tractor, do not forget to connect 'plus' to

'plus' and 'minus' to 'minus'. If replacement of a part of charging circuit is done, disconnect a battery from the

earth electrode of the tractor by battery disconnector (-). Any incidental short circuits on clamps are

excluded.

With any manipulation or starter repair, it is necessary to disconnect the minus pole of the

battery and to shift all the levers including PTO shaft shifting lever to neutral position so as to

prevent spontaneous start and endangering the life of a repairman.

It is forbidden to start by short circuiting the clamps of starter. Start tractor only from driver's

seat.

Accumulator battery

Battery disconnector

If the tractor is put aside for a longer period of time, it is necessary to recharge the

accumulator at least once in three months because of the battery self discharge. When putting

tractor aside we recommend you to disconnect the accumulator by means of battery disconnector.

Attention! When the engine is switched off, the engine control unit remains active for about

2 minutes because of storage of operation data. During this time the supply of current from the

accumulator must not be interrupted. Do not disconnect the accumulator before this time expires.

Accumulator battery is located in a box on the left side of

the tractor. After unscrewing the screw marked with an

arrow, lid of box of accumulator battery can be opened

together with steps.

NM13N076

Accumulator battery is located under the cab on the right

side. Battery disconnector (1) is located on the right side

of the tractor in front of the cab.

a - Battery connected

b - Battery disconnected

NM13N77

ELECTRIC INSTALLATION

Содержание MAJOR HS Series













































































































































Результаты поиска

Содержание MAJOR HS Series

Отзывы:

Бренды по названию

Популярные бренды

Zetor MAJOR HS Series, Руководство оператора

Результаты поиска

Содержание MAJOR HS Series

Отзывы:

Бренды по названию

Популярные бренды