Zetor MAJOR HS Series Скачать руководство пользователя страница 110 | Manualshive

Страница: 110 / 140

Zetor MAJOR HS Series Скачать руководство пользователя страница 110

Most of operations of planned maintenance may be carried out by the driver or other user of the tractor. In
case you do not have sufficient technical equipment, let the difficult operations carried out by a specialised
repair shop.

All works, connected with cleaning, lubrication and adjustments of the tractor or coupled

mechanisms may only be carried out after stopping of the engine and other movable components

except checks of brakes, recharging and hydraulic system

.

Front bonnet opening
Opening the bonnet:
Unlock the bonnet by pulling the draw bar (1) in the direction of an arrow, grip where the arrows are and
heave.
The bonnet is locked in the heaved position by a gas-fluid prop.

Closing the bonnet:
Pull the bonnet by means of a belt, grip where the arrows are and snap in the downward direction so that the
lock of bonnet snaps down.

Checking oil levels in engine

Rapid closing of the bonnet may damage

filaments of bulbs in headlights in the front mask.

NM13N107

Perform the check daily before starting the operation when
the tractor is standing horizontally and the engine is not
running. The engine oil dipstick (1) is located on the right
side of the engine. The filling hole (2) is located in the left
side of the engine.

Take out the dipstick (1), wipe it with a clean cloth without
fibres and insert it back till the end.
When the dipstick is taken out again check the oil level.
The oil level must always be in the range from MIN and
MAX.
Add the oil as necessary through the filling hole (2).

NM15D63

MAINTENANCE INSTRUCTIONS

109

«
...
108
109
110
111
112
...
»

Содержание MAJOR HS Series













































































































































Отзывы:

Нет отзывов