Zetor MAJOR HS Series Скачать руководство пользователя страница 122 | Manualshive

Страница: 122 / 140

background image

Filtration elements cleaning

Tractor's safety cab is not equipped with special filters for air sucked into the cab.

It does not protect operators against the effects of aerosols and other harmful substances!

Draining the condensate from air collector

Air condition maintenance

The main element of air condition system maintenance is cleaning air condition condenser (is

placed in front of engine radiator).

Clogged air condition condenser decreases not only the efficiency of cooling system but also the

efficiency of engine cooling.

Regenerate filtration elements of the cab depending on
the degree of clogging:
- by dusting
- by blowing with compressed air
Check clogging daily. Replace strongly polluted filters.

NM13N110

Air collector is placed on the right side of the tractor under
the cab. Draining the condensate from air collectorto be
done by deviation of venting valve by pulling a ring. Valve
is located on the bottom part of air collector.

NM13N074

Open the bonnet, demount the nut (1) and protrude the
radiator to the side and blow with compressed air or wash
with pressed water (against the direction of tractor drive).
Slide the radiator back in and attach properly. Mind proper
conducting of hoses to oil radiator.

E740

MAINTENANCE INSTRUCTIONS

121

«
...
120
121
122
123
124
...
»

Содержание MAJOR HS Series













































































































































Отзывы:

Нет отзывов

Похожие инструкции для MAJOR HS Series

Бренд: Craftsman Страницы: 68

Craftsman 944.601901

Бренд: Sears Страницы: 60

Бренд: Ventrac Страницы: 31

Бренд: Daedong Страницы: 372

Бренд: Cub Cadet Страницы: 61

Бренд: Mahindra Страницы: 28

Бренд: CAMSO Страницы: 24

Бренд: Textron Страницы: 74

Бренд: Belle Group Страницы: 200

Profile GCG1580L

Бренд: GE Страницы: 2

Reboke 6000 TSI

Бренд: Stara Страницы: 69

Бренд: Rousseau Страницы: 2

Бренд: Fox Страницы: 20

Бренд: Case IH Страницы: 24

Бренд: Case HI Страницы: 6

Бренд: Case IH Страницы: 41

Бренд: Case IH Страницы: 35

Бренд: Case IH Страницы: 51

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды