![background image](http://html1.mh-extra.com/html/zenoah/htz2460/htz2460_operators-manual_3456343012.webp)
STARTING AND STOPPING
12 – English
Check before starting
•
Inspect the working area. Remove any objects that
could be thrown out.
•
Check the cutting attachment. Never use blades that
are dull, cracked or damaged.
•
Check that the machine is in perfect working order.
Check that all nuts and screws are tight.
•
Make sure the gear housing is lubricated correctly.
See instructions under the heading Gear housing.
•
Check that the cutting attachment always stops when
the engine is idling.
•
Only use the machine for the purpose it was intended
for.
•
Make sure that the handle and safety features are in
good working order. Never use a machine that lacks a
part or has been modified outside its specifications.
•
All covers must be correctly fitted and undamaged
before you start the machine.
Starting and stopping
Cold engine
Ignition:
Set the stop switch to the start position.
Primer bulb:
Press the air purge repeatedly until fuel
begins to fill the bulb. The bulb need not be completely
filled.
Choke:
Set the choke control in the choke position.
Warm engine
Ignition:
Set the stop switch to the start position. (Run
position)
Primer bulb:
Press the air purge repeatedly until fuel
begins to fill the bulb. The bulb need not be completely
filled.
Starting
Hold the body of the machine on the ground using your
left hand (CAUTION! Not with your foot!). Grip the starter
handle, slowly pull out the cord with your right hand until
you feel some resistance (the starter pawls grip), now
quickly and powerfully pull the cord.
Never twist the
starter cord around your hand.
Push the choke control back to its original position as
soon as the engine fires, and continue trying to start until
the engine starts.
!
WARNING! The complete clutch cover
and gear housing must be fitted before
the machine is started, otherwise the
clutch may come loose and cause
personal injury.
Always move the machine about 3
metres from the refuelling position
before starting. Place the machine on a
firm surface. Remember that the blades
may start to move when the engine is
started. Make sure the blades cannot
come into contact with any object. Make
sure that no unauthorised persons are in
the working area, otherwise there is a
risk of serious personal injury. The safety
distance is 15 metres.
H1159003-38_1,HTZ2460 west Page 12 Monday, February 11, 2019 9:02 AM
Содержание HTZ2460
