background image

GB-6

G3000

Gaining a good footing at the working position can be 
assisted by use of a temporary foot stirrup created from 
an endless sling.

Starting the saw in the tree

When  starting  the  saw  in  the  tree,  the  operator 
should:
a)  apply the chain brake before starting;
b)  hold saw on either the left or right of the body when 

starting:

1)  on the left side hold the saw with either the left hand 

on  the  front  handle  or  the  right  hand  on  the  rear 
handle and thrust the saw away from the body while 
holding the pull starter cord in the other hand;

2)  on the right side, hold the saw with the right hand 

on either handle and thrust the saw away from the 
body while holding the pull starter cord in the left 
hand.

The  chain  brake  should  always  be  engaged  before 
lowering a running saw onto its strop.
Operators should always check the saw has sufficient 
fuel before undertaking critical cuts.

One-hand use of the chainsaw

Operators should not use tree service chainsaws one-
handed  in  place  of  unstable  work  positioning  or  in 
preference to a handsaw when cutting small diameter 
wood at the branch tips.
Tree  service  chainsaws  should  only  be  used  one-
handed where:
•  the operator cannot gain a work position enabling 

two-handed use; and

•  they need to support their working position with one 

hand; and

•  the saw is being used at full stretch, at right angles 

to and out of line with the operator’s body.

Operators should never:
•  cut with the kickback zone at the tip of the chainsaw 

guide bar

•  ‘hold and cut’ sections
•  attempt to catch falling sections.

Freeing a trapped saw

If the saw should become trapped during cutting, op-
erators should:
•  switch off the saw and attach it securely to the tree 

inboard (i.e. towards the truck side) of the cut or to 
a separate tool line;

•  pull the saw from the kerf whilst lifting the branch as 

necessary;

•  if necessary, use a handsaw or second chain saw to 

release the trapped saw by cutting a minimum of 30 
cm away from the trapped saw.

Whether  a  handsaw  or  a  chainsaw  is  used  to  free  a 
stuck saw, the release cuts should always be outboard 
(toward the tips of the branch), in order to prevent the 
saw being taken with the section and further complicat-
ing the situation.

Содержание G3000



















Отзывы: