background image

32

English

6. OPERATION

REFUELING

• Refuel the fuel tank in a flat

place outdoors. Avoid smoking
or bringing any flame or spark
near the fuel, and stub out any
cigarette.

• When refueling the fuel tank

while using this machine, make
sure to stop the engine and
allow it to cool before refueling
the fuel tank.

• Make sure to tighten the fuel-

tank cap firmly.

• Wipe up all fuel spills with a dry

cloth before starting the engine.

Fill the fuel tank to roughly 80% of its
capacity.
If filled too full, the fuel may leak from
the tank cap while using this
machine.

1. Place the brushcutter to be

refueled in a flat place outdoors,
and make sure it is stable.

2. Unscrew the fuel-tank cap a little,

and allow the difference of
atmospheric pressure between the
inside and outside of the fuel tank
to equalize.

3. Remove the fuel-tank cap, and fill

fuel little by little up to roughly
80%.

4. After filling the fuel, close the fuel-

tank cap tightly, and make sure
that the fuel does not leak.

(1) Tank cap
(2) Fuel tank

IMPORTANT

WARNING

OP1

■급유

●연료 탱크에 급유할 때는 실외의 평

평한 장소에서 실시해 주십시오. 급

유시는 화기를 멀리하고 담배불은 

꺼 주십시오.

●작업 도중에 급유할 경우에는, 반드

시 엔진을 끄고 식은 다음 실시해 

주십시오.

●연료 뚜껑은 확실하게 조여 주십시

오.

●급유시에 흘린 연료는 엔진을 시동

하기 전에 걸레로 잘 닦아 주십시

오.

●연료 탱크에 급유할 때는 흘리지 않

도록 해 주십시오.

●연료를 너무 많이 넣으면 운전시 캬

뷰레터로부터 새어 나올 우려가 있

습니다.

1.급유할 예초기를 실외의 평탄한 장

소에 놓아 주십시오.

2.연료탱크 뚜껑을 약간 느슨하게 하

여, 연료탱크 내부와 외부와의 압력

차를 제거해 주십시오.

3.연료탱크의 뚜껑을 열고, 흘리지 

않도록 하여 조금씩 급유해 주십시

오.

4.급유가 끝나면 탱크 뚜껑을 확실하

게 조여서 연료가 흘러 나오지 않는 

것을 확인해 주십시오.

(1)뚜껑

(2)연료탱크

Содержание BK2650DL-Hb

























































Отзывы: