background image

6

to sound level and hours of operations for
the product.

BEFORE STARTING THE ENGINE

1. The area within a perimeter of 15 m of

the person using the product should be
considered a hazardous area into
which no one should enter. If
necessary, yellow warning rope,
warning signs should be placed around
the perimeter of the area. When work
is to be performed simultaneously by
two or more persons, care should also
be taken to constantly look around or
otherwise check for the presence and
locations of other people working so as
to maintain a distance between each
person sufficient to ensure safety.

2. Check the condition of working area to

avoid any accident by hitting hidden
obstacles such as stumps, stones,
cans, or broken glass. 

Remove any obstacle before beginning
work.

3. Inspect the entire unit for loose

fasteners and fuel leakage. Make sure
that the cutting attachment is properly
installed and securely fastened. 

4. Be sure the cutting attachment guard is

firmly attached in place. 

5. Always use the harness. Adjust the

harness for comfort before starting the
engine. The harness should be
adjusted so the left hand can
comfortably hold the handlebar grip
approximately waist high. 

STARTING THE ENGINE

1. Keep bystanders and animals at least

15 m away from the operating point. If
you are approached, immediately stop
the engine. 

2. The product is equipped with a

centrifugal clutch mechanism, so the
cutting attachment begins to rotate as
soon as the engine is started by putting
the throttle trigger into the start
position. When starting the engine,
place the product onto the ground in a
flat clear area and hold it firmly in place

IMPORTANT

so as to ensure that neither the cutting
part nor the throttle trigger come into
contact with any obstacle when the
engine starts.

Never place the throttle trigger into the
high-speed position when starting the
engine.

3. After starting the engine, check to

make sure that the cutting attachment
stops rotating when the throttle is
moved fully back to its original position.
If it continues to rotate even after the
throttle trigger has been moved fully
back, turn off the engine and take the
unit to your authorized ZENOAH
servicing dealer for repair.

USING THE PRODUCT

Cut only materials recommended by the
manufacturer. And use only for tasks
explained in the manual. 

1. Grip the handles firmly with both hands

using your whole hand. Place your feet
slightly apart (slightly further apart than
the width of your shoulders) so that
your weight is distributed evenly across
both legs, and always be sure to
maintain a steady, even posture while
working.

2. Keep cutting attachment below waist

level. 

3. Maintain the speed of the engine at the

level required to perform cutting work,
and never raise the speed of the
engine above the level necessary.

4. If the unit starts to shake or vibrate,

turn off the engine and check the
whole unit. Do not use it until the
trouble has been properly corrected.

5. Keep all parts of your body away from

rotating cutting attachment and hot
surfaces.

6. Never touch the muffler, spark plug, or

other metallic parts of the engine while
the engine is in operation or
immediately after shutting down the
engine. Doing so could result in

IMPORTANT

WARNING

4. Safety precautions

Содержание BC4301FW





















Отзывы: