Zelmer ZVC265SP, Руководство пользователя

Страница: 58 / 60

64
ZVC265-001_v02
Preparing the vacuum cleaner
for operation
1 Press the side button on the end of the suction hose.
2
Place the end of the suction hose in the vacuum cleaner.
You should hear a distinctive click, if you do it right.
3 Attach the other end of the hose (the handle) to the
suction tube.
4
Adjust the length of the telescopic suction tube by sliding
the slider according to the arrow and pull out/ pull the tube
together.
5 Assemble the proper nozzle or brush to the other end of
the suction tube.
6
Use combination carpet & floor brush for vacuuming both
hard surfaces and carpets. To clean hard surfaces – wooden
floors, plastic floors, ceramic tiles etc. pull out the brush by
pressing the switch on the combination brush according
to the figure . Retract the brush when vacuuming
carpets (set the switch in “ ”).
7
Pull the plug and cord (3) out of the vacuum cleaner.
While pulling out the cord, pay attention to the
yellow stripe which signals the end of the cord.
Further attempts (pulling on cord) may result in
damaging the cord.
8
Plug in the appliance.
Before turning the vacuum cleaner on, check whether the
CYKLON dust container is installed in the chamber of the
vacuum cleaner, and whether the inlet and outlet filters are
installed in the vacuum cleaner.
9
Switch on the vacuum cleaner by pressing the “on/off”
button (7) .
10 The vacuum cleaner is equipped with a suction power
regulation control. The power is controlled by means of
a knob.
11
Turning the knob according to the label increases or
respectively decreases the suction power.
Filter disassembly
Before changing the filters make sure that the vacuum cleaner
is switched off and unplugged from the mains supply.
INLET FILTER CONE
It is necessary to clean the inlet filter cone from time to time.
1
Remove the CYKLON dust container and empty it
according to paragraph (F) .
2 Release the fastening of the EPA basic filter (14) and
remove it from the CYKLON dust container.
3 Press the button situated on the CYKLON dust container
and open the bottom of the container.
4 Turn the inlet filter cone (17) clockwise.
5 Remove the inlet filter cone from the CYKLON dust
container.
B
C
6 If the inlet filter cone (17) is dirty, it may be rinsed
with running water. Remember to dry the cone before its
reinstallation.
Pay attention to the gasket placed on the
bottom of the cone collar. Do not lose it.
7 Place a new/rinsed inlet filter cone into the socket in
such a way that the two protrusions placed on the collar are
situated under the fastening in the body of the container.
8 The cone should be pressed tightly and turned to the
limit counterclockwise. A characteristic click notifies about
a proper installation.
9 Snap the bottom of the CYKLON dust container.
10 Place the EPA basic filter (14) . Pay attention so that the
two protrusions on the bottom part of the EPA basic filter (14)
find their way into the holes of the dust container.
11
Place the CYKLON dust container in the chamber of the
vacuum cleaner. A characteristic click notifies about a proper
installation.
BASIC EPA FILTER & FOAM FILTER
It is necessary to clean the basic EPA filter from time to time,
as it is contaminated with dust.
●
Uninstall the CYKLON dust container and empty it
according to paragraph (F) .
1
Release the fastening of the EPA basic filter (14) and
remove it from the CYKLON dust container.
2 Remove the foam filter (15) . If the foam filter (15) is dirty,
it may be washed with running water. Remember to dry it off
before reinstalling the filter.
The main function of the foam filter
(15) is protecting the
basic EPA filter (14) from excessive dirt.
Due to safety reasons it is forbidden to install
a wet or damaged foam filter (15).
●
Clean the pleads of the basic EPA filter (14) , if any of
them are damaged, the filter definitely must be replaced.
If the basic EPA filter (14) is dirty, it may be washed with
running water. Remember to dry it off before reinstalling
the filter.
Due to safety reasons it is forbidden to install
a wet or damaged basic EPA filter (14).
●
Place the foam filter back into its place.
3
Put the new/rinsed EPA basic filter (14) back in its place
– pay attention to put the two protrusions in the bottom part
of the EPA basic filter (14) in the holes of the dust container.
A characteristic click notifies about a proper installation.
4 Place the CYKLON dust container with the installed
basic EPA filter (14) in the chamber of the vacuum cleaner.
A characteristic click notifies about a proper installation.
D