Zelmer ZVC165EF, Руководство пользователя

Страница: 49 / 52

55
ZVC165-001_v03
4 In case of the telescopic suction tube adjust the
necessary tube length by moving the slider according to the
slide in/slide out direction arrow.
5 Assemble the appropriate nozzle or brush to the other
end of the suction tube.
6 Use combination carpet & floor brush for vacuuming both
hard surfaces and carpets. To clean hard surfaces – wooden
floors, plastic floors, ceramic tiles etc. pull out the brush by
pressing the switch on the combination brush according
to the figure . Retract the brush when vacuuming
carpets (set the switch in “ ”).
7
Pull the plug and cord (3) out of the vacuum cleaner.
While pulling out the cord, pay attention to the
yellow stripe which signals the end of the cord.
Further attempts (pulling on cord) may result in
damaging the cord.
8
Plug in the appliance.
Before operation make sure that the SAFBAG bag is
installed in the vacuum cleaner chamber and that inlet filter
and the outlet filter is installed in the appliance.
9 Switch on the vacuum cleaner by pressing the “on/off”
button (4) .
10 The vacuum cleaner is equipped with suction adjustment
knob, which allows smooth regulation of the vacuum cleaner
power. Power is regulated with the use of the knob. If you
turn the knob (in the direction of max or min sign), you
will increase or decrease suction power depending on the
direction (ZVC165EK, ZVC165EF type).
Filter disassembly
Before changing the filters make sure that the vacuum cleaner
is switched off and unplugged from the mains supply.
INLET FILTER
1 Release the catch of front cover (9) and open it.
2 Pull the bag out of the chamber (see p. E).
3
Remove the inlet filter (11) out of the housing.
4 Put a new filter paying attention to insert it entirely into
the outlet.
5 Insert a bag into the vacuum cleaner chamber (see p. E).
6 Close the front cover of the vacuum cleaner.
The damaged inlet filter should be replaced with
a new, genuine manufactured product only.
“MICROFILTER” OUTLET FILTER
1 Push the outlet filter cover blockade and open it.
2
Take out worn-out outlet filter.
3 Put a new filter paying attention to insert it precisely in its
place.
4
Close the outlet filter cover – the outlet filter cover
blockade should slam. Characteristic “click” means that the
outlet filter cover is correctly mounted.
C
D
Always replace a damaged inlet filter only with
a brand new one.
Dust bag disassembly/assembly
1 If the bag repletion indicator is entirely covered by
orange diaphragm whereas suction tube or brush is lifted
over refined surface, it means that you have to change a dust
bag. The bag repletion indicator may start as the result of
clogging of suction hose or other elements connected with it.
2
Switch off the vacuum cleaner by pressing the on/off
button (4) .
●
Unplug the appliance.
3
Pull the end of the hose out of the inlet opening of the
vacuum cleaner.
4 Release the front cover fastening (9) and open the cover.
5 Holding the dust bag plate, slightly pull it out of the bag
handle.
6
Insert the new bag plate between handle slide and
insert it to the handle ending. Then spread the dust bag in
the whole chamber. The direction of dust bag mounting is
indicated by arrow on a bag plate or on a bag.
7 Close the cover until you hear the characteristic clicking
sound – be careful not to catch the bag.
Do not vacuum without bag. In case if there is
no bag in the vacuum cleaner, the front cover
of the vacuum cleaner cannot be locked.
Zelmer vacuum cleaners are equipped with dust bags in the
quantity given in the Chart. It is recommended to change the
dust bag, if you notice that:
a) orange field covers the bag repletion indicator,
b) the vacuum cleaner operates poorly,
c) the dust bag is full.
The number of SAFBAG bags set that can be purchased,
is placed on a sticker located in the vacuum chamber.
Special accessories
The following special accessories may be purchased in retail
outlets:
Parquet brush “BNB” (19)
Is used to clean and polish hard, scratch sensitive surfaces
such as wooden floors, floor panels, parquet, marble, tiles, etc.
Delicate and soft natural bristles ensure maximum vacuum
effectiveness and protects against scratching the cleaned
surface.
End of operation cleaning
and maintenance
1 Switch off the vacuum cleaner by pressing the “on/off”
button (4) .
2 Unplug the appliance.
E
F