![background image](http://html1.mh-extra.com/html/zelmer/mm1500-987/mm1500-987_user-manual_928288033.webp)
37
987-008_v02
7a
Food tray
7b
I
Adaptor
II
Shredder bowl
(the mincer may be equipped with one set of bowls
7a
or
7b
)
8
Pusher
And additional accessories:
9
Base plate
10
Sausage filler nozzle
11
Mincer screen with 8 mm openings
12
Mincer screen with 2,7 mm openings
Mechanical safety device for the motor
13
Scroll
14
Clutch
15
Screw M5x20
The mincer is equipped with a mechanical safeguard, which
protects the motor against damage – the teeth in the clutch
break when the mincer is overloaded (e.g. when bones get
inside).
Replace the damaged clutch:
●
twist off the screw
(15)
from the scroll with the damaged
clutch,
●
remove the damaged clutch
(14)
,
●
attach the new clutch and tighten it with the screw
(15)
.
„Reverse” function
The motor has a special function allowing to temporarily
change the direction of the scroll. It is used if mincing is
limited and/or if there is too much product in the mincer body
(the scroll does not take the product). Press the
„
R”
switch
for a short period of time, the product will be removed from
the inside of the mincer body. Press the
„I”
button once
again to continue operation.
If the scroll is still blocked by the excess of product, use the
„R”
switch once again, remove the product from the mincer
body and next remove product parts which make it difficult to
mince (e.g. sinews, etc.).
In some cases it is necessary to dismantle the mincer body
and remove the above-mentioned obstacles.
Working with the mincer unit
Insert the following parts into the mincer body
(2)
:
1
Insert the scroll
(3)
with the coupling facing inside.
2
Fit the knife
(4)
onto the pin of the scroll
(3)
.
3
Place the screen
(e.g. 5)
over the knife so that the
protrusion in the mincer body will fit into the groove in the
circumference of the screen.
4
Tightly fit all the elements of the mincer unit.
5
Fit the assembled mincer unit onto the drive unit
(1)
and
turn it until you hear a click of the lock. It means that the body
has been properly installed.
A
E
6a
Place the tray
(7a)
on the mincer body
(2)
.
6b
Insert the adaptor
I
into the bowl
II
. Mount the bowl
and the adaptor
(7b)
on the mincing chamber
(2)
.
Preparing the appliance for operation
and switching on the appliance
●
Take out a sufficient length of the supply cord and the
appropriate accessories from the compartment.
1
Place the motor
(1)
near the socket, on a hard, stable
surface. Do not cover the ventilation openings of the housing.
●
Open the compartment on the back of the housing and
take out an appropriate screen
(Fig.
C
)
.
A screen with 4 mm openings is installed in the
mincer body as a standard.
●
Wash all accessories thoroughly before the initial use.
●
Assemble the appropriate accessories and install them
on the motor.
2
Plug in the appliance.
3
Switch on the appliance using the
„I”
switch
(1a)
(the appliance starts to operate after about 2 seconds).
Operation with the sausage filler nozzle
Insert the following parts into the mincer body
(2)
:
1
Insert the scroll
(3)
with the coupling facing inside.
2
Fit the insert
(9)
onto the pin of the scroll
(3)
.
3
Fit the sausage stuffing tube
(10)
.
4
Tightly fit all the elements with the threaded ring
(6)
.
5
Fit the assembled mincer unit onto the drive unit
(1)
and
turn it until you hear a click of the lock.
6a
Place the tray
(7a)
on the mincer body
(2)
.
6b
Insert the adaptor
I
into the bowl
II
. Mount the bowl
and the adaptor
(7b)
on the mincing chamber
(2)
.
Soak the casing for about 10 minutes before fitting.
●
Fit the wet casing on the sausage filler nozzle.
Make sure the not to block the ventilation
openings on the nozzle.
The meat cannot be „too thin”. A large liquid
content may cause its leakage to the inside of
the mincer.
Juicer
The juice squeezer is an equipment included to some
types of mincers. It allows to squeeze juice from fruits such
as: raspberries, currants, strawberries, gooseberry and
additionally from grapes and tomatoes. Berry fruits such
as currants can be squeezed with stalks. Fruits with large
stones for example plums, cherries etc can be squeezed in
the appliance after removing the stones.
D
F
I
Содержание MM1500/987
Страница 38: ...Notes ...