Zelmer Elf 2 323, Руководство пользователя

Страница: 42 / 42

46
E
B
Appliance elements
1 Combination brush fastening
2 Outlet filter cover
3 Plug and cord
4 ON/OFF button
5 Suction adjustment knob (323.0 type)
6 Bag repletion indicator
7 Cord rewind button
8 Handle
9 Front cover fastening
10 Suction hose
11 Inlet filter (installed in the vacuum cleaner)
12 “Microfilter” outlet filter (installed in the vacuum cleaner)
13 Telescopic suction tube (type 323.0 EK)
14 Segmented suction tubes (type 323.5 EF, 323.0 EF)
15 Paper bag (2 items)
16 Small brush
17 Small nozzle
18
Crevice nozzle
19 Switchable combination brush
20 Parquet brush “BNB” (additional equipment – may be
bought in retail centers)
21 Turbobrush (additional equipment – may be bought in
retail centers)
22 SAFBAG dust bag (additional equipment – may be
bought in retail centers)
Preparing the vacuum cleaner
for operation
1 Pull the end of the suction hose into the opening and
press lightly.
2
Attach the other end of the hose (the handle) to the
suction tube.
3 Join both segments of the suction tube together.
4
In case of the telescopic suction tube adjust the
necessary tube length by moving the slider according to the
slide in/slide out direction arrow.
5 Assemble the appropriate nozzle or brush to the other
end of the suction tube.
6 To clean hard surfaces – wooden floors, plastic floors,
ceramic tiles etc. pull out the brush by pressing the switch on
the combination brush according to the figure .
7 Pull the plug and cord (3) out of the vacuum cleaner.
ATTENTION! While pulling out the cord, pay attention
to the yellow stripe which signals the end of the
cord. Further attempts (pulling on cord) may result in
damaging the cord.
8 Plug in the appliance.
Before operation make sure that the SAFBAG bag is installed
in the vacuum cleaner chamber and that inlet filter and the
outlet filter is installed in the appliance.
9 Switch on the vacuum cleaner by pressing the “on/off”
button (4) .
10 The vacuum cleaner is equipped with suction adjustment
knob, which allows smooth regulation of the vacuum cleaner
power. Power is regulated with the use of the knob. If you
turn the knob (in the direction of max or min sign), you
will increase or decrease suction power depending on the
direction (323.0 type).
Filter disassembly
Before changing the filters make sure that the vacuum cleaner
is switched off and unplugged from the mains supply.
INLET FILTER
1 Release the catch of front cover (9) and open it.
2
Pull the bag out of the chamber (see p. E).
3 Remove the inlet filter (11) out of the housing.
4 Put a new filter paying attention to insert it entirely into
the outlet.
5
Insert a bag into the vacuum cleaner chamber (see p. E).
6 Close the front cover of the vacuum cleaner.
ATTENTION! The damaged inlet filter should be replaced
with a new, genuine manufactured product only.
“MICROFILTER” OUTLET FILTER
1
Push the outlet filter cover blockade and open it.
2 Take out worn-out outlet filter.
3 Put a new filter paying attention to insert it precisely in its
place.
4 Close the outlet filter cover - the outlet filter cover
blockade should slam. Characteristic “click” means that the
outlet filter cover is correctly mounted.
ATTENTION! Always replace a damaged inlet filter only
with a brand new one.
Dust bag disassembly/assembly
1 If the bag repletion indicator is entirely covered by
orange diaphragm whereas suction tube or brush is lifted
over refined surface, it means that you have to change a dust
bag. The bag repletion indicator may start as the result of
clogging of suction hose or other elements connected with it.
2 Switch off the vacuum cleaner by pressing the on/off
button (4) .
3 Unplug the appliance.
4 Pull the end of the hose out of the inlet opening of the
vacuum cleaner.
5 Release the front cover fastening (9) and open the cover.
6 Holding the dust bag plate, slightly pull it out of the bag
handle.
A
C
D