60
491-012_v01
2
Take the rubber lid off and place the mixing attachment
onto the drive in an open position following the instructions on
the drive and lid’s case. Then twist the drive shaft clockwise
(the direction is shown by the arrow) until you hear that it has
clicked (the indicator on the coupling should be in a closed
position.
3
Plug the power cord to the power supply socket.
4
Plunge the coupling in the products to be mixed.
5
Then start – up the appliance pressing the
(2)
switch and
set the required gear as necessary.
The appliance operates only with the “power”
or “turbo” button pressed.
When finished, turn the appliance off and unplug it by
●
disconnecting the cable cord from the power outlet.
Operational guidelines
To detach the plastic shaft, just follow the attaching
●
procedure in reverse order.
Wash the plastic shaft by swishing it in clean, warm water.
●
If any fluid gets inside the blender attachment, turn it and
●
put with the blade up until it is dry.
When the mixing attachment is dry
●
(6)
put the rubber lid
on
(6a)
to keep the attachment safe.
Included in the set you will find a special
beaker with a handle for mixing, which is easy
and helpful to operate with. Other jars may be
used as well.
USING WHISK ATTACHMENT
ZELMER hand blender with the whisk attachment purees
soups, whips up your favourite smoothies, mayonnaise or
creams and toppings for waffles and desserts, as well as
rubs egg yoke with sugar or prepares dough for pancakes.
Before assembling on and removing the whisk,
make sure, that the plug of the supplying cord
is disconnected from the socket.
1
Before operation insert the whisk into the gearbox.
2
Such assembled attachment attach to the drive shaft,
align them in the position according to the indicators on the
cover of the drive shaft and the whisk attachment. Then
twist the drive shaft clockwise (the direction is shown by the
arrow) until you hear that it has clicked (the indicator on the
coupling should be in a closed position).
3
Plug the power cord to the power supply socket.
4
Plunge the end of the whisk inside the beaker into products.
5
Then start – up the appliance pressing the switch
(2)
and
set the required gear as necessary.
The appliance operates only with the “power”
or “turbo” button pressed.
When finished, turn the appliance off and unplug it by
●
disconnecting the cable cord from the power outlet.
G
Operational guidelines
To detach the whisk attachment, just follow the attaching
●
procedure in reverse order.
For best results operate the appliance at high gear –
●
15th speed setting.
When finished, turn the appliance off and unplug it by
●
disconnecting the cable cord from the power outlet.
You can also use the mixing container included with the
●
blender.
To obtain better results lean the whisk is
a small angle and make round movements with
it inside the bowl.
The level of products placed in a bowl should
not exceed the height of the workspace of the
beater (L).
3 cm
L
OPERATING THE MINI FOOD PROCESSOR
ZELMER hand blender is equipped with a mini food
processor used to chop meat, cheese, nuts, onions, garlic,
carrots, and prunes.
Before assembling on and removing the
blender drive out of the mini food processor,
make sure that the plug of the supplying cord
is disconnected from the mains supply outlet.
Operate the blender so, that the closed/open marking
located on the appliance are well visible.
Before each usage of the mini food processor knife,
●
remove the cover out of the blades.
1
Before use put the rubber anti-skidding lid – mat
(13a)
at
the bottom of the housing base. Then, place the blade into
the work bowl so that its hole matches the tang inside.
2
Put the food to be processed into the container. Fill in the
container. Do not exceed the marked MAX level.
3
Put the cover-transmission on the container. Make sure
the protrusions fit the openings in the container and turn the
lid clockwise until stop.
4
Place the blender motor in open position
on such
assembled mini food processor, in accordance with the
indicator on the motor casing and the lid of the mini food
processor including gearbox.
5
Turn the motor clockwise relative to the transmission
(according to the direction of the arrow) until you hear a click
(the indicator on the transmission should be in the closed
position ).
6
Plug in the appliance. Switch on the appliance pressing
the switch
(2)
.
7
Set the required gear as necessary.
D
Содержание 491 symbio
