41
B
Appliance elements
1
Handle
2
Cord rewind button
3
Combination brush fastening
4
Plug and cord
5
Outlet filter cover
6
ON/OFF button
7
Suction power regulation slider
8
Dust bag full indicator
9
Electrobrush socket (type 4000.0 HP, 4000.0 HQ)
10
Accessory compartment cover
11
Front cover fastening
12
Suction hose
13
Telescopic suction tube
14
SAFBAG dust bag
15
SAFBAG dust bag module (with the installed SAFBAG
dust bag)
16
Outlet filter HEPA H13 (installed in the vacuum cleaner)
17
Inlet filter casing (installed in the vacuum cleaner)
18
Inlet filter (installed in the vacuum cleaner)
19
Parquet brush “BNB”
Is used to clean and polish hard, scratch sensitive surfaces
such as wooden floors, floor panels, parquet, marble, tiles,
etc.
Delicate and soft natural bristles ensure maximum vacuum
effectiveness and protects against scratching the cleaned
surface.
20
Small nozzle
21
Small brush
22
Crevice nozzle
23
Combination brush. The vacuum cleaner is equipped
with only one type of combination brush (A or B)
A
Switchable combination brush
B
Combination brush with a small item separator
24
Turbobrush (type 4000.0 HT)
25
Electrobrush (type 4000.0 HQ)
Preparing the vacuum cleaner
for operation
1
Insert the curved hose end in the opening of the vacuum
cleaner and gently press. A characteristic click indicates that
the hose has been properly installed.
2
Connect the other end of the hose (handle) with the
telescopic suction tube. In order to do so press the locking
device
“A”
and slide the tube into the hose handle so that
the locking device
“A”
is blocked in opening
“B”
.
3
Adjust the length of the telescopic suction tube by sliding
the slider according to the arrow and pull out/ pull the tube
together.
4
Assemble the appropriate nozzle or brush to the other
end of the suction tube.
5
You may assemble a basket for picking up small objects
in the combination brush with the small item separator.
In order to do so remove the blank cover and insert the basket.
6
To clean hard surfaces – wooden floors, plastic floors,
ceramic tiles etc. pull out the brush by pressing the switch on
the combination brush according to the figure
.
7
The vacuum cleaner is equipped with locker for
accessories. In order to open the locker, pick up the handle
of vacuum cleaner and pull upwards the cover of the locker
for accessories
(10)
.
8
The accessories may be attached to the accessory
holder in the suction hose handle. This way they will be
available for use at any time.
9
The button of power cable coiler is located under the
handle of vacuum cleaner (from the right). This place has
been marked by the sign on the handle. Press the handle
in marked place and pull out the cable.
ATTENTION! While puling out the cord pay attention
to the yellow stripe which signals the end of the
cord. Further attempts (pulling on cord) may result in
damaging the cord.
10
Plug in the appliance.
Before operation make sure that the SAFBAG bag is installed
in the vacuum cleaner chamber and that inlet filter and the
HEPA outlet filter is installed in the appliance.
11
Switch on the vacuum cleaner by pressing the “on/off”
button
(6)
.
12
The vacuum cleaner is equipped with electronic power
regulator allowing a stepless regulation of vacuum cleaner
power. The power regulation is performed with a slider.
13
Moving the slider according to its mark (+ or –) will
increase or reduce the suction power.
14
The vacuum cleaner is equipped with the “Parksystem”
function. This function allows to temporarily switch off the
vacuum cleaner using the fastening hook of the combination
brush without the necessity to use the on/off button. In order
to do so, during operation insert the fastening hook of the
combination brush in the combination brush fastening
(3)
.
The vacuum cleaner will automatically switch off.
Filter disassembly
Before changing the filters make sure that the vacuum
cleaner is switched off and unplugged from the mains
supply.
INLET FILTER
1
Release the catch of front cover
(11)
and open it.
2
Remove the SAFBAG dust bag module from the vacuum
cleaner chamber.
A
C
