Zelmer 32Z010, Руководство пользователя

Страница: 38 / 42

40
GW32-003_v02
Dear Customers,
Congratulations on your choice of our appliance, and
welcome among the users of Zelmer products.
In order to achieve best possible results we recommend
using exclusively original Zelmer accessories. They have
been specially designed for this product.
Please read these instructions carefully. Pay your special
attention to important safety instructions, in order to avoid
accidents during operation and/or avoid damage of the
appliance. Keep this Instruction for future reference.
Important safety instructions
Warning!
Risk of property damage
Connect the appliance to 230 V mains supply.
●
Do not unplug by pulling on cord.
●
The supplying cord shall not be hanged over the edge
●
of the table or board, nor touch any hot surface.
Do not fill the jug in with boiling liquids.
●
Keep the stand blender and supplying cord away from
●
hot surfaces and burners.
If it is possible, store the stand blender away from
●
direct sun radiation and glow-like light.
Never store with lid closed on the blender jug. Damp
●
the lid gasket with water before usage, and insert the
lid on the jug.
Do not overflow the jug. In case the liquid gets under
●
the motor housing, it can be vacuumed into the motor,
causing its damage.
Do not fill the jug over 1250 ml mark – in such case,
●
the content of the jug can lift the lid when the motor
starts up
It can be operated not longer than 3 minutes, without
●
interruption in constant or pulsating mode („ Pulse ” and
„ Ice Crush ” features), otherwise it can get overheated.
After 3 minutes of operation, switch off the appliance
for at least 10 minutes, and let the motor cool down.
Do not operate when the jug is empty, as it can get
●
overheated.
Use the soft brush for washing metal parts, especially
●
the sharp blades.
Tip
Product information and tips on its use
Read the whole instruction for use before you start
●
using your stand blender.
The stand blender is intended for domestic usage only.
●
In case it is used for gastronomic business purposes,
warranty terms and conditions change.
EN
Danger! / Warning!
Risk of injury
Always place the appliance on flat, plain surface.
●
Always unplug the appliance when it is not in use and
●
before cleaning.
Do not operate the appliance if the cord, the housing or
●
the handle is visibly damaged. In such a case, return
the appliance to a service center.
If the non-detachable part of the cord is damaged,
●
it should be replaced by the producer or at a proper
service point or by a qualified person in order to avoid
any hazards.
The appliance should be repaired by trained staff only.
●
Improper repair can result in serious hazard for a user.
In case of defects we recommend you to contact
qualified service desk.
Do not immerse motor housing in water or any other
●
liquid; do not use it in bathroom and outdoors.
Press „
●
Off ” button, before you remove the lid of the jug
and remove the jug from the motor housing, wait until
the blades stop completely.
Do not use stand blender without feeder opening
●
stopper.
Do not put your hands inside the jug, even if it is
●
removed for cleaning, as the cutting blades are still
dangerous – very sharp.
Do not put any objects (spoon, etc.) into the jug, when
●
the blender is connected to power supply.
Do not wash the cutting blades directly with hand.
●
This appliance is not intended for use by persons
●
(including children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by
a person responsible for their safety.
Children should be supervised to ensure that they do
●
not play with the appliance.
Make sure you understand well above mentioned
instructions.
Safety recommendations
The stand blender has thermal protection, which turns off
the device at the moment of overheating. In this case, it is
necessary to disconnect the device from the power source.
Remove the plug from the contact, then wait at least 10
minutes, allowing the motor to cool down. After this time, you
can re-attach the stand blender.