![background image](http://html1.mh-extra.com/html/zelmer/32z010/32z010_user-manual_3321126039.webp)
41
GW32-003_v02
Specifications
You can find the appliance technical data on the name plate.
Admissible time of non-stop operation: 3 minutes.
An interval between repeated operations: 10 minutes.
Speed range: 1-14.
Noise level at gear 14: 90 dB/A.
The stand blender is built in II class of insulation
.
It does not require connecting to mains supply socket with
earthing.
The stand blender meets the requirements of effective
standards.
The appliance meets the requirements of the following
directives:
Low Voltage Device (LVD) – 2006/95/EC.
–
Electro- Magnetic Compatibility (EMC) – 2004/108/EC.
–
The product is marked with CE symbol on the name plate.
Outline
(Fig. A)
1
Feeder opening stopper
2
Lid
3
Blender jug
4
Control light
5
„
On
” switch
6
„
Off
” switch
7
„
Pulse
” switch
8
Handle
9
Blocking ring
10
Blades
11
Gasket
12
Motor housing
13
Speed control knob
14
„
Ice Crush
” button
15
Anti-slip flange
Handling and operation
(Fig. B)
PREPARATION FOR OPERATION
Before first usage (or after long storage) wash the jug
(3)
,
lid
(2)
and feeder opening stopper
(1)
in hot water with
washing-up liquid, rinse and dry well. Keep your hands away
from cutting blades
(10)
– they are sharp.
OPERATION MANUAL
1
Place the motor housing
(12)
on dry, firm, and horizontal
surface, near mains supply outlet and out of the reach of
children.
Arrange the supplying cord so that it does not hang from the
table or board and it can not be pulled or dragged by accident.
2
Connect the plug into the mains supply outlet.
3
Place the jug
(3)
so, that the protrusions at the bottom
part of the jug
(3)
were fitted with the protrusions in top part
of motor housing
(12)
.
The handle (8) of the blender jug (3) shall be
placed on the right side of the appliance.
4
Put the ingredients into the jug
(3)
.
Do not fill in over
1250 ml
marked on the blender jug
(3)
. In such case,
the content of the jug can lift the lid
(2)
when the motor
starts up.
5
Insert the lid
(2)
on the jug
(3)
before you use the stand
blender.
6
Turn the lid
(2)
counter-clockwise („
Lock
” position) until
it stops in the cut in the top part of the handle
(8)
. Make sure,
that the lid
(2)
is properly inserted in blender jug
(3)
it means
that the protrusion at the lid
(2)
is aligned with the handle
(8)
, otherwise remove it and assemble once again. When
the lid is properly assembled, the control light
(4)
shall glow
pulsating which means that the appliance is ready for use.
Before you insert the lid (2) moisture the lid
gasket with water.
The motor driver is equipped with micro-switch,
which enables the appliance operation only
when the lid (2) is properly closed on the blender
jug (3). Otherwise the motor shall not start up.
7
Insert the feeder opening stopper
(1)
on the feeder opening
of the lid
(2)
. Adjust the cuts on the stopper
(1)
with the arrow
on the lid
(2)
while inserting the stopper
(1)
and turn it right or
left until it runs in order to assemble it properly.
Do not start the stand blender without the feeder opening
stopper
(1)
, especially, when you use solid ingredients. They
can be thrown out of the opening.
8
Press „
On
” button
(5)
. Control light
(4)
shall permanently
glow with red light, which means that the appliance is in
operation.
9
Turn the speed control knob
(13)
into required position:
Speed
Dish
Instructions and recommendations
Speed 1 to 3
Frozen fruit pulp.
Place frozen fruit pulp inside the jug, with recommended amount of water (maximum
1250 ml). Mix for some seconds. Do not mix too long, in order to avoid appearing
air bulbs.
Preparing instant meals for
people on diet: desserts,
powdered milk, etc..
Place all ingredients in the jug. Operate the appliance (10 to 15 seconds) until you
obtain homogenous consistence. At first operate with
„Pulse”
function in order to
prevent appearing air bulbs.
Vinaigrette sauce.
Start from cutting thick ingredients and herbs, operating short with
„Pulse”
function
and then add remaining ingredients and mix with constant speed for 15 to 20
seconds. Make sure the blades are covered with the ingredients, to avoid splashing.
Содержание 32Z010
