47
32Z010-001_v04
seconds at lowest speed applying safety instructions. Then
empty the jug
(3)
, turn it upside down and dry it.
3
If necessary, clean the jug
(3)
, lid
(2)
, feeder opening
stopper
(1)
and blades
(10)
in warm water with wash-up liq
-
uid. Then rinse it under clean running water and dry. At first
disassemble cutting unit
(10)
(see “Cutting unit disassem
-
bling”).
●
If you left the jug for longer time without cleaning and
some particles glued to the jug inner, use nylon brush.
●
We do not recommend cleaning the jug
(3)
, blades
(10)
,
lid
(2)
and feeder opening stopper
(1)
in dish washer.
Aggressive cleaning agents applied in such device can
influence negative the surface conditions.
4
Clean the outsider of the motor housing
(12)
with damp,
gentle cloth.
Do not immerse the motor housing (12) in
water or other liquid.
●
Do not clean the outside of the housing
(12)
with
aggressive detergents such as emulsion milk or pastes,
etc. They can remove information graphic symbols.
●
Do not clean the transparent jug
(3)
with harsh sponges
or clothes.
●
After washing dry thoroughly all the parts of the
appliance.
CUTTING UNIT DISASSEMBLING
●
Unplug from the mains supply outlet.
●
Empty the jug (
3)
.
●
Remove the lid
(2)
from the jug
(3)
turning it clockwise
(
“Open”
position).
●
Turn the jug
(3)
upside down and place the appliance on
flat, plain surface.
●
Turn the blocking ring counter clockwise. Remove
carefully with a gasket.
The cutting blades are sharp. Handle them
carefully.
CUTTING UNIT ASSEMBLING
●
Turn the blades upside down in order to assemble them
and insert at first the
gasket
at the jug opening flange
(3)
and blades inside the jug
(3)
.
●
Insert blocking ring and turn it clockwise until it runs,
when the protrusion on blocking ring gets to the handle
(8)
. Make sure that the blocking ring is screwed to the jug
(3)
. It influences the tightness of the connection.
●
After assembling, turn the jug
(3)
upside down and place
it on the motor housing
(12)
so, that the protrusions in
bottom part of the jug
(3)
are fitted with the protrusions
top part of the motor housing
(12)
.
The handle
(8)
of the blender jug
(3)
shall be placed on the
right side of the appliance.
10
“Pulse” function
●
Pressing “
Pulse
”
(7)
button shall cause short operation
with maximum speed, disregarding set blades speed.
“
Pulse
”
(7)
button is pressed with a spring. When we
stop pressing it, the appliance shall stop the operation.
Use “
Pulse
”
(7)
as you like, but remember, that it works
with maximum speed, so you have to control what is
going on with the ingredients, unless you want to achieve
a pulp.
●
Do not operate longer than 3 minutes, otherwise it can
get overheated. After 3 minutes, switch it off for at least
10 minutes, so that the engine cools down.
●
If you need to add some new ingredients during blender
operation, turn and lift feeder opening stopper
(1)
, feed
the ingredients into the opening, then replace the stopper
again
(1)
and turn it left or right until it runs.
●
Make sure, that the ingredients you add, shall not
increase the capacity inside the jug exceeding 1250 ml
marking on the jug
(3)
.
11
“Ice Crush” function
●
Check if the stand blender is clean, before you use it for
crushing ice. Otherwise wash it thoroughly with clean
water. Any residues of washing agent can influence the
taste of crushed ice and shall cause that the drink we
add the ice to, shall loose its taste.
●
In case you want to crush ice, use 6 to 10 ice cubes
in given time, and then add 15 ml (1 spoon) fresh cold
water.
●
Insert the lid
(2)
including feeder opening stopper
(1)
on the appliance and turn it counter clockwise (“
Lock
”
position). Press the “
Ice Crush
”
(14)
button 3 or 4 times,
with short intervals between pressing. Too long crushing
time makes the ice become water; too short time shall
crush the edges/corners of the ice cubes only. Do not try
to crush the ice without adding some water into the jug.
12
Press “
Off
”
(6)
button, before you remove the lid
(2)
from
the jug
(3)
or remove the jug
(3)
from the motor housing
(12)
;
wait until the cutting blades
(10)
stop.
After operation
●
Hold the motor housing
(12)
with one hand, catch the
handle
(8)
with the latter hand, then lift the jug
(3)
up and
remove it from the motor housing
(12)
.
●
Remove the lid
(2)
from the jug
(3)
turning it clockwise
(“
Open
” position).
●
Unplug the appliance from the mains supply outlet when
it is not in use.
Cleaning and maintenance
1
Unplug from the mains supply outlet before cleaning.
Clean after operation as soon as possible, to prevent the
pulp accumulation inside the jug
(3)
.
2
To clean the jug and the blades it is recommended to
apply self-cleaning function. Pour about 1 litre of water into
the jug
(3)
and start up the appliance for approximately 30
C
Содержание 32z010-001
