background image

22

HDVI5 Component Video Switch 

23

HDVI5 Component Video Switch

Changing Switching Delays

The HDVI5 allows adjusting the switching delay times, for Video and 
Audio, independently.  By default the HDVI5 uses a 200ms video and 
audio delay when switching between channels. The HDMI specifi-
cations calls for a minimum of 00ms, some monitors may require 
much larger delay times to switch reliably.

To adjust the Audio/Video switching delays...

Step 1: Place the HDVI5 into the Setup Mode

The HDVI5 is placed into the setup mode by pressing and 

holding the Power button for about  seconds.

Step 2: Enter the Switching Delay Setup Mode

Press the '5' button to enter the Switching Delay Setup 

Mode.
The blue LEDs indicate the Video mute delay, if there are no 

blue LEDs lit, then there is no video delay.
The ted LEDs indicate the Audio mute delay, if there are no 

ted LEDs lit, then there is no audio delay.
 

No LEDs lit 

 

 

= 0 sec delay.

• 

One left justified LED 

= 50ms delay.

•• 

Two left justified LEDs 

= 00ms delay.

••• 

Three left justified LEDs  

= 200ms delay.

••••  Four left justified LEDs 

= 300ms delay.

•••••  Five LEDs 

 

 

= 500ms delay.

 ••••  Four right justified LEDs 

=  sec delay.

  •••  Three right justified LEDs 

= 2 sec delay.

   ••  Two right justified LEDs 

= 3 sec delay.

    •  One right justified LED 

=  sec delay.

Step 3: Adjust Switching Delay Times

The 'SEL' button toggles between the Video delay setting 

and the Audio delay setting.
The 'A' and 'A2' buttons are used to set the delay times
'A' decreases the delay time.
'A2' increases the delay time.
Press the Power button to save new settings and exit.

Note: 

The new settings are saved in non-volatile memor y and 
are not affec ted by a power failure.




1                        2                        3                        4                        5                      SEL                     A1          A2

Step 1: Place the HDVI5 into the Setup Mode

Press and hold the Power Button until the 

display goes wild.  (About  seconds.)

Step 2: Enter the Switching Delay Setup  Mode.

1                        2                        3                        4                        5                      SEL                     A1          A2

After pressing '5', the standby 
LED continues to flash, and the 
front panel will display the cur-
rent delay settings.

Step 3: Adjust Switching Delay Times

1                        2                        3                        4                        5                      SEL                     A1          A2

Toggle between audio

 and video  delays

Decrease delay

Increase delay

Exit setup mode

Содержание HDVI5


























Отзывы: