background image

14 - EN

EN - 15

3.2.3  STATUS (read only)

Menu item

Function

CURRENT ERRORS

To view the codes of the current errors.

UNIT

To view the information about the unit.

  HRU TYPE: view the type name of the unit;

  FIRMWARE VERSION: view the firmware version of the unit;

  SERIAL NUMBER: view the serial number of the main board in the unit.

SCHEDULER

To view the scheduler step in which the unit is currently running.

  VENTILATION: view which step of the ventilation scheduler is in operation;

  COMFOCOOL3: view which step of the ComfoCool Q600 scheduler is in operation.

TEMP. AND HUMIDITY

To view the current temperature and humidity of the airflows.

  EXTRACT AIR TEMP.: view the current temperature of the extract airflow;

  EXTRACT AIR HUM.: view the current humidity level of the extract airflow;

  EXHAUST AIR TEMP.: view the current temperature of the exhaust airflow;

  EXHAUST AIR HUM.: view the current humidity level of the exhaust airflow;

  OUTDOOR AIR TEMP.: view the current temperature of the outdoor airflow;

  OUTDOOR AIR HUM.: view the current humidity level of the outdoor airflow;

  SUPPLY AIR TEMP.: view the current temperature of the supply airflow;

  SUPPLY AIR HUM.: view the current humidity level of the supply airflow.

BYPASS STATE

To view the current state of the heat recovery control (bypass). 

  The percentage of bypassed air is shown.

FROST UNBALANCE

To view the current state of airflow unbalance caused by the frost protection function.

  The percentage of supply air reduction is shown.

FROST PREHEATER3

To view the current state of the preheater caused by the frost protection function.

  The current power of the preheater is shown.

POSTHEATER3

To view the current state of the post-heater.

  The percentage of the post-heater control is shown.

ANALOG INPUT3

To view the current state of the analog input(s)

  0-10V 13: view the voltage level of the first analog input.

  0-10V 23: view the voltage level of the second analog input.

  0-10V 33: view the voltage level of the third analog input.

  0-10V 43: view the voltage level of the fourth analog input.

SUBSOIL HEAT EXCH.3

To view the current state of the regulated subsoil heat exchanger (e.g. ComfoFond-L Q).

  STATE: view the current state of the regulated subsoil heat exchanger pump;

  OUTDOOR AIR TEMP.: view the current outdoor air temperature;

  GROUND TEMPERATURE: view the current temperature of the regulated subsoil heat exchanger 

brine liquid.

COMFOCOOL3

To view the current state of the ComfoCool Q600.

  STATE: view the current ComfoCool Q600 mode and the current ComfoCool Q600 supply air 

temperature;

  CONDENSER TEMP: view the current condenser temperature.

SEASON DETECTION 

To view the current season detection state.

  SEASON: view the current season mode;

  LIMIT RMOT HEAT: view the set RMOT4 below which the (central) heating system is normally active;

  LIMIT RMOT COOL: view the set RMOT4 above which the (central) cooling system is normally 

active;

  CURRENT RMOT: view the current RMOT4.

FANS

To view the current state of the fans

SUPPLY FAN

  FAN SPEED: view the current speed of the fan.

  FAN DUTY: view the current duty of the fan.

  FLOW: view the current airflow of the fan.

EXTRACT FAN

  FAN SPEED: view the current speed of the fan.

  FAN DUTY: view the current duty of the fan.

  FLOW: view the current airflow of the fan.

ENERGY

To view the energy consumption and saved energy.

POWER CONSUMPTION

  VENTILATION: view the current electrical consumption of the fans.

  PREHEATER: view the current electrical consumption of the preheater.

  YEAR TO DATE: view the energy consumption of the fans since the beginning of the year.

  TOTAL: view the total energy consumption of the fans since the moment of commissioning.

AVOIDED HEATING

  ACTUAL POWER: view the current avoided heating power.

  YEAR TO DATE: view the avoided heating energy since the beginning of the year.

  TOTAL: view the avoided heating energy since the moment of commissioning.

AVOIDED COOLING

  ACTUAL POWER: view the current avoided cooling power.

  YEAR TO DATE: view the avoided cooling energy since the beginning of the year.

  TOTAL: view the avoided cooling energy since the moment of commissioning. .

TOTAL SAVINGS

  YEAR TO DATE: to view the total energy savings since the beginning of the year.  

  TOTAL: to view the total energy savings since the moment of commissioning.

3 This menu is only visible when the accessory is connected to the unit.

4 RMOT = running mean outdoor temperature (average temperature over past five days).

Содержание ComfoAir Q 350 ST





































Отзывы: