background image

17 

 

9.2

 

  Operation notice 

*

Leave at least 7 cm bottom strap out for easy sealing (As Figure 17 shown) 

 

9.3

 

  Operation notice for fiber baling and strapping system application: 

9.3.1

 

Keep at least 2 cm space between each sealing joint for multiple joints sealing. 

9.3.2

 

ZAPAK ZP-SW25 sealer is applicable to seal and connect the two strap 

rolls  of  their  tail  and  head  together  on  strapping  system.  Suggest  to  adjust  the 

sealing  time  longer  than  usual  to  get  a  deeper  seal.  Trim  off  the  overflow  on 

both  sides  of  the  sealing  joint  to  ensure  the  straps  go  through  the  track  of 

strapping system smoothly

.

 

 

10

 

Copyright Notice 

This document is copyrighted in 2019 by Pantech International Inc. All rights 

are reserved.    Pantech International Inc., reserves the rights to make 

improvements to the products described in this manual at any time without 

notice. 

 

No part of this manual may be reproduced, copied, translated or transmitted in 

any form or by any means without the prior written permission of Pantech 

International Inc.    Information provided in this manual is intended to be 

accurate and reliable.    However, Pantech International Inc. assumes no 

responsibility for its use, nor for any infringements upon the rights of third 

parties which may result from its use. 

 

 

 

 

PANTECH INTERNATIONAL INC. 

Taipei, Taiwan, R.O.C. 

© 2019 Pantech International Inc.    All rights reserved. 

Worldwide Patent Pending 

Printed in Taiwan, R.O.C. 

ZAPAK is a registered trademark of Pantech International Inc. 

Product and specifications are subject to change without notice. 

One year limited manufacturer warranty   

 

Printed in Taiwan 2019 

 

Содержание ZP-SW25






















Отзывы: