REMOTE GSM SWITCH GRM-10
MANUAL INSTRUCTION
ZAMEL
Sp. z o.o.
ul. Zielona 27, 43-200 Pszczyna, Poland
Tel. +48 (32) 210 46 65, Fax +48 (32) 210 80 04
www.zamelcet.com
, e-mail: [email protected]
The device is designed for single-
phase installation and must be installed
in accordance with standards valid in a
particular country. The device should
be connected according to the details
included in this operating manual.
Installation, connection and control should be car-
ried out by a qualified electrician staff, who act in
accordance with the service manual and the device
functions. In case of casing dismantling an electric
shock may occur, and the guarantee is lost then.
Before installation make sure the connection cables
are not under voltage. The cruciform head screw-
driver 3,5 mm should be used to instal the device.
Improper transport, storage, and use of the device
influence its wrong functioning. It is not advisable
to instal the device in the following cases: if any
device part is missing or the device is damaged or
deformed. In case of improper functioning of the de-
vice contact the producer.
CAUTION
APPEARANCE
FEATURES
TECHNICAL PARAMETERS
DESCRIPTION
● Remote control of the electrical de-
vices by means of commands (in-
coming phone connection, text mes-
sage) sent from a mobile phone,
● Comfortable control of difficult ac-
cess devices (air conditioning, heat-
ing, etc.),
● Two relay outputs with the load ca-
pacity of 16 A,
● Operation is optically signalled (pow-
er supply, relay status, GSM modem
status)
● Low power consumption, a possibility
of continuous operation.
The GRM-10 device is designed to
realise simple control and notice opera-
tions. The operations are carried out by
means of the GSM network. The control-
ler has two independent outputs with a
maximum load capacity of 16 A / 250 V
AC. Two digital inputs allow for a link with
the alarm control panels. The RS485 in-
terface in connection with the RXM-01
translator gives a possibility to control
EXTA FREE system receivers with the
help of a mobile phone and messages
that are defined by the user. The number
of operation modes and configuration
options make the GRM-10 a very useful
device for simple home automation and
industrial systems. The GRM-10 device
is made in a three-MOD casing and is
designed for mounting in switchboards
on a TH35 rail.
GRM-10
Nominal input rated voltage: 230 V AC 50 / 60 Hz
Input voltage tolerance: -15 ÷ +10 %
Nominal power consumption: 1,5 W
GSM frequency: 900/1800/1900 MHz
Operating range: restricted by the GSM network
Supply voltage optical signalling: LED diode (green)
GSM status signalling: LED diode (yellow)
Output number: 2
Output status signalling: 2 x LED diode
Output relays parameters: 2 x NO 16 A / 250 V AC AC1 4000 VA
Input number: 2
Input type: Digital - pot4 V
Interfaces: RS485 MODBUS - A,B,C terminals; USB;
PK1, PK2 push-buttons
RS485 transmission signalling: LED diode
Position on RS485 bus: only MASTER
Ambient temperature range: -10 ÷ +55
o
C
Operating position: free
Casing mounting: TH35 rail
Casing protection degree: IP20 (PN-EN 60529)
Protection class: II
Overvoltage category: II
Pollution degree: 2
Dimensions: 3-modular casing
Weight: 163 g
Reference standard: PN-EN 60950-1:2007; PN-EN 55024:2000;
PN-EN 61000-4-4
The symbol means selective
collecting of electrical and electronic
equipment. It is forbidden to put the
used equipment together with other
waste.
plik: inst_ext_pl_grm-10_gb | modyfikacja: 03.06.2013
Input terminals
RS485 Interface
Power supply signalling
GSM range signalling
Relay 1 (LEDP1)
status signalling
SIM card input
Relay 2 (LEDP2)
status signalling
GSM antenna
RS-485 transmission
signalling
MICRO USB input
Power supply terminals
Output terminals
PK1, PK2 push-buttons
