Z3 Technology Z3-DME-02 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 44

background image

40

CONFIDENTIAL

DOC-USR-0054-02

____________________________________________________________________________________

Z3 Technology, LLC

♦

100 N. 8th St. STE 250

♦

Lincoln, NE 68508-1369 USA

♦

+1.402.323.0702

update

Can be used to change the bitrate without
stopping/restarting an encode session (see
Section

Error! Reference source not

ound.

, “Using “update” to change the

bitrate dynamically,” on page 16).

clone

Duplicate CH tab (can be used to quickly
copy CH1 values to CH2, for example).

delete

Used to delete excess tabs created by Clone.

(status)

IDLE
STOPPED
RUNNING
POLLING

Current status of the encoder. “POLLING”
indicates “start” was pressed and the
encoder is waiting for valid input data to be
detected.

Note 1: Input Resolutions Supported:

WQVGA (320x180), QVGA (320x240), SIF (352x240), CIF (352x288), 2-CIF (352x576), 640x360,

VGA (640x480), 4-CIF (704x576), 16:9 PAL (1024x576), D1 PAL (720x576), D1 NTSC (720x480),

     720p (1280x720), XGA (1280x1024), 1080p (1920x1080), Follow input

     “Follow input” = Generate encoder resolution based on capture resolution detected

Note 2:  GOP Sizes Supported:

     10, 12, 15, 25, 30, 50, 60, 100, 120, 200, 240 frames

«
...
38
39
40
41
42
...
»

Содержание Z3-DME-02













































Отзывы:

Нет отзывов

Похожие инструкции для Z3-DME-02

Бренд: Sabaj Страницы: 18

Бренд: Wacker Neuson Страницы: 254

Бренд: Lantronix Страницы: 142

Бренд: Future Illuminations Страницы: 2

CO-SinusUPS-400W

Бренд: Adler Power Страницы: 4

Бренд: Lampizator Страницы: 32

Бренд: Wacker Neuson Страницы: 36

Бренд: Cable-Tronix Страницы: 4

Бренд: ICP DAS USA Страницы: 8

Бренд: Vanner Страницы: 28

Бренд: FONESTAR Страницы: 9

Бренд: Mitsubishi Страницы: 143

Q.VOLT-G2 HYB-4.6kW.1.1

Бренд: Q CELLS Страницы: 118

Бренд: Samlexpower Страницы: 3

Бренд: Wagan Страницы: 36

Бренд: American Audio Страницы: 40

Бренд: UCView Страницы: 4

Бренд: Synthrotek Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды