manualshive.com logo in svg

Z3 Technology Z3-DME-02, Инструкция пользователя, Страница: 21 / 44

Поделиться
Скачать
Z3 Technology Z3-DME-02 Скачать руководство пользователя страница 21

21

 

 
  

CONFIDENTIAL     

                                    

DOC-USR-0054-02 

 

____________________________________________________________________________________

 

Z3 Technology, LLC 

♦

 100 N. 8th St. STE 250 

♦

 Lincoln, NE 68508-1369 USA 

♦

 +1.402.323.0702 

(33)

 

Now go back to the System Setup tab.  Go to the bottom of the screen and select as the preset the 

“z3_test” configuration you just created: 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

(34)

 

 As soon as you select “z3_test”, the screen will reload.  Go ahead and check “Use DHCP”:  

 

 
 
 
 
 
 
 
 
 
 
 
 

(35)

 

 Now that DHCP is set in z3_test, save the configuration by clicking on the “Save” button:  

 

 
 
 
 
 
 
 
 
 
 

(1) Click on “System Setup” 
Tab 

Select “z3_test” 
preset 

Figure 22  Selecting “z3_test” within the System Setup Tab 

 

Check “Use DHCP” 
again 

Figure 23  Setting DHCP 

 

Click “Save” 

Figure 24  Saving Preset Values 

 

Содержание Z3-DME-02













































Отзывы:

Нет отзывов