Z-Wave PAN30 Скачать руководство пользователя

Страница: 19 / 19

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the re-

ceiver is connected.

•

Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject

to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may

cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the party respon-

sible for compliance could void the user's authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other an-

tenna or transmitter.

Содержание PAN30




















Результаты поиска

Содержание PAN30

Отзывы:

Похожие инструкции для PAN30

Бренды по названию

Популярные бренды

Z-Wave PAN30, Руководство пользователя

Результаты поиска

Содержание PAN30

Отзывы:

Похожие инструкции для PAN30

Бренды по названию

Популярные бренды