background image

 

10 

Z-FLEX® LIMITED LIFETIME WARRANTY 

 

Z-FLEX® (“Seller”) extends the following LIMITED WARRANTY for Z-VENT (the “Z-Vent”):  

     Seller  warrants  that  at  the  time  of  purchase,  the  Z-Vent  will  be  free  of  manufacturer’s  defects  in  material  and/or 

workmanship. This warranty shall extend to the original purchaser of the Z-Vent or, if purchased by a contractor, to the end 

user. This warranty is valid for a period of fifteen (15) years from the date of purchase, provided that the Z-Vent has been 

installed according to Z-Flex® installation instructions. Deviating from the installation and use instructions included with the Z-

Vent will void the warranty. 

      Under this Limited Warranty, Seller’s sole responsibility and liability shall be to replace the Z-Vent and/or 

accessories,  if  found  by  Seller  to  be  defective  according  to  the  terms  of  the  warranty,  and  shall  not  include  replacement 

installation or other costs. 

 

IMPORTANT: 

The Z-Vent is designed for use with Category II, III and IV furnace and boiler venting and should not be used 

with any other type of furnace and boiler venting. Use of the Z-Vent with any other type of furnace and boiler venting other 

than those recommended by Seller for use with its Z-Vent will void the warranty. 

WARNING:  CONDENSATION  WITH  HIGH  ACID  CONTENT  MAY  BE  PRODUCED  DUE  TO  UNFORESEEN 

CONDITIONS.  YOUR  HEATING  APPLIANCE  AND  VENTING  SYSTEM  SHOULD  BE  INSPECTED  BY  A  LICENSED 

CONTRACTOR  ON  AN  ANNUAL  BASIS  FOR  POSSIBLE  SIGNS  OF  DETERIORATION  DUE  TO  RUSTING  OR  PIN 
HOLES.  CONDENSATION  WITH HIGH ACID CONTENT MAY CAUSE LEAKAGE OF HARMFUL GASES WHICH CAN 

CAUSE NAUSEA, FAINTING OR DEATH. IF DETERIORATION IS DETECTED CEASE USE OF HEATING SYSTEM AND 

CALL FURNACE/BOILER INSTALLER FOR REMEDIAL ACTION.

 

        To activate the warranty, the end-user must complete and return the Z-Flex® Warranty Registration Card within ninety 

(90) days of installation of the Z-Vent. Upon written notice of any defects, Z-Flex® reserves the right to examine or establish 

reasonable proof of defective material or workmanship justifying replacement. 

NO OTHER EXPRESS WARRANTY HAS BEEN MADE OR WILL BE MADE ON BEHALF OF SELLER WITH RESPECT TO 

THE  Z-VENT  OR  THE  INSTALLATION  OR  REPLACEMENT  OF  THE  Z-VENT.  SELLER  SHALL  NOT  BE  LIABLE  FOR 

ANY SPECIAL, INCIDENTAL, INDIRECT OR CON-SEQUENTIAL DAMAGES. 

         As  some  jurisdictions  do  not  allow  the  exclusion  or  limitation  of  incidental  or  consequential  damages,  the  above 

limitations or exclusions may not apply to you. 

IMPLIED WARRANTIES, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR 

PURPOSE, IMPOSED ON THIS SALE UNDER STATE LAW, ARE LIMITED TO THE PERIOD DURING WHICH THIS 

WARRANTY  IS  IN  EFFECT.  AS  SOME  JURISDICTIONS  DO  NOT  ALLOW  LIMITATIONS  ON  THE  LENGTH  OF  AN 

IMPLIED WARRANTY, THE ABOVE LIMITATION MAY NOT APPLY TO YOU. 

Claims  under  this  Warranty  must  be  made  within  the  warranty  period  in  writing  and  directed  to:  In

  the  USA; 

Warranty 

Claims, Z-Flex®(US) Inc., 20 Commerce Park North, Bedford, New Hampshire 03110, (603) 669-5136 or (800) 645-5600. 

In 

Canada; 

Warranty Claims, Z-Flex® Inc., 452 Attwell Drive, Etobicoke, Ontario, M9W 5C3, (416) 679-0045. 

This Warranty gives you specific legal rights, and you may also have other rights that vary in different States and Provinces.

 

 

 

WARRANTY REGISTRATION CARD: Z-FLEX® 

      For this warranty to be effective, this card must be completed upon purchase of the covered Z-Vent and returned to Z-

Flex® within ninety (90) days of installation of the Z-Vent. 

Original end-user’s name

:__________________________________________________________________________ 

Address of premises in which the Z-Vent is installed

:___________________________________________________ 

________________________________________________________________________________________________ 

Z-Vent purchased from

:___________________________________________________________________________  

Date of Installation

:_______________________________________________________________________________  

Type of Heating System into which Z-Vent installed

:___________________________________________________ 

I understand and agree to the Warranty as stated

:_____________________________________________________ 

 

__________________________________                               ____________________________ 

Signature

                                                                              

   Date

 

 

  

 

Flexmaster Canada Limited 

Model SVEIII Instructions Ver. 4.3 Oct. 2010

 

Содержание Z-Vent SVE III Series











Отзывы: