background image

DP-2010RX Version 06042001 ATEX Rev.

YZ Systems, Inc. • 3101 Pollok Drive • Conroe, Texas • USA • 77303 • P: 936.788.5793 • F: 936.788.5720

35

Diagram #9
DuraSite (illustrated)

P/N C6-1002 (Ser. #4088+)

Set Screw

P/N C0-0099

P/N A3-0155

Knob

P/N C6-1003 (Ser. #4608+)

Magnet Assembly

Piston

P/N C6-1004

Piston Washer

YZ UniValve

P/N A5-4222B

P/N A5-2222

Back-Up Washer

O-Ring

Product Head

Stainless Steel

P/N C6-1000

P/N C0-0048

Hex Nuts

Valve Seat

P/N A3-0063

Purge Valve Nut

P/N A3-0080

P/N A8-0013

Magnetic Volume Indicator

P/N C6-1203 (DS-150)

P/N C6-1303 (DS-300)

P/N C6-1403 (DS-500)

P/N C6-1503 (DS-800)

P/N C6-1603 (DS-1000)

Gauge

P/N A3-0083

Rupture Disc

P/N A3-0084

YZ UniValve

P/N C6-1001

Pre-Charge Head

P/N A3-0095

Valve Stem Assembly

P/N A3-0062

Seat Retaining Washer

P/N A3-0063

Valve Seat

P/N C6-1200 (DS-150)

P/N C6-1300 (DS-300)

P/N C6-1400 (DS-500)

P/N C6-1600 (DS-1000)

P/N C6-1301 (DS-300)

P/N C6-1401 (DS-500)

P/N C6-1501 (DS-800)

P/N C6-1601 (DS-1000)

P/N C6-1201 (DS-150)

P/N C6-1500 (DS-800)

Cylinder

Rupture Disc Nut

Tie Rod

Mixing Ball

Snap Ring

P/N C3-0018

Piston Seal

P/N A5-2021

P/N A6-0023

O-Ring

P/N C6-1005

P/N 12-1008 (Ser. #0614 - #4087)

P/N 12-1007 (Ser. #0322 - #0613)

P/N 12-1019 (Ser. #0614 - #4607)

P/N 12-1006 (Ser. #0321 and Prior)

P/N 12-1018 (Ser. #0613 and Prior)

Содержание DP-2010RX




































Отзывы:

Похожие инструкции для DP-2010RX