manualshive.com logo in svg
background image

JOHNSON CONTROLS

FORM 160.80-EG1 (808)

Introduction

The YORK 

Millennium

 YS Chiller offers a complete com-

bination of features for total owner satisfaction.

MATCHED COMPONENTS MAXIMIZE EFFICIENCY

Actual chiller efficiency cannot be determined by analyzing 

the theoretical efficiency of any one chiller component. 

It  requires  a  specific  combination  of  heat  exchanger, 

compressor, and motor performance to achieve the low-

est system kw/Ton. YORK 

Millennium

 chiller technology 

matches chiller system components to provide maximum 

chiller efficiency under actual – not just theoretical – op

-

erating conditions.

REAL-wORLD ENERGY PERFORMANCE

Johnson Controls pioneered the term “Real-world energy” 

to  illustrate  the  energy-saving  potential  of  focusing  on 

chiller performance during off-design conditions. Off-de-

sign is not only part load, but full load operation as well, 

with  reduced  entering  condenser  water  temperatures 

(eCwTs). This is where chillers operate 99% of the time, 

and where operating costs add up.

The YS 

Millennium

 chillers are the only chillers designed 

to operate on a continuous basis with cold eCwT and full 

condenser flow at all load points, taking full advantage of 

Real-World conditions. This type of operation benefits the 

cooling tower as well; reducing cycling of the fan motor 

and ensuring good coverage of the cooling fill.

YORK 

Millennium

 chillers offer the most efficient Real-

world operation of any chiller, meaning lower operating 

costs and an excellent return on your chiller investment.

OPEN DRIVE DESIGN

Hermetic-motor burnout can cause catastrophic damage 

to a chiller. The entire chiller must be cleaned, and the 

refrigerant  replaced.  YORK 

Millennium

  screw  chillers 

eliminate this risk by utilizing air-cooled motors. Refrig-

erant never comes in contact with the motor, preventing 

contamination of the rest of the chiller.

Insurance companies that offer policies on large air condi-

tioning equipment often consider air-cooled motors a sig-

nificant advantage over hermetic refrigerant cooled units.

HIGH-EFFICIENCY HEAT EXCHANGERS

Millennium

 chiller heat exchangers offer the latest tech-

nology in heat transfer surface design to give you maxi-

mum  efficiency  and  compact  design.  Water-side  and 

refrigerant-side  design  enhancements  minimize  both 

energy consumption and tube fouling.

FACTORY  PACKAGING  REDUCES  FIELD  LABOR 

COSTS

YORK 

Millennium

  screw  chillers  are  designed  to  keep 

installation costs low. where installation access is not a 

problem, the unit can be shipped completely packaged, 

requiring minimal piping and wiring to complete the in-

stallation.

For  those  units  utilizing  a  factory  installed  Solid-State 

Starter, the three power leads provide all power to the 

chiller and its auxiliaries.

TAKE ADVANTAGE OF COLDER COOLING TOwER 

wATER TEMPERATURES

YORK 

Millennium

 screw chillers are designed to take full 

advantage of colder cooling tower water temperatures, 

which are naturally available during most operating hours. 

Considerable energy savings are available by letting tower 

water temperature drop, rather than artificially holding it 

above  75°F  (23.9°C),  especially  at  low  load,  as  some 

chillers require.

U.L. ACCEPTANCE  –  YOUR ASSURANCE OF RELI-

ABILITY

YORK 

Millennium

 screw chillers are approved for listing 

by Underwriter’s Laboratories for the United States and 

Canada. Recognition of safety and reliability is your as-

surance of trouble-free performance in day-to-day building 

operation.

Содержание YS

























































Отзывы: