background image

JOHNSON CONTROLS

6

FORM 160.79-PW2 

ISSUE DATE: 01/31/2019

LIST OF FIGURES

FIGURE 1 

- Remote Mode Ready to Start Contacts .................................................................................................9

FIGURE 2 

- Cycling Shutdown Contacts ...................................................................................................................9

FIGURE 3 

- Safety Shutdown Contacts ....................................................................................................................9

FIGURE 4 

- Run Contacts (Compressor #1) ...........................................................................................................10

FIGURE 5 

- Run Contacts (Compressor #2) ...........................................................................................................10

FIGURE 6 

- Anticipatory/Alarm Contacts.................................................................................................................10

FIGURE 7 

- Remote Start-Stop Contacts from Energy Management Systems ......................................................10

FIGURE 8 

- Remote/Local Cycling Devices Compressor #1 .................................................................................. 11

FIGURE 9 

- Remote/Local Cycling Devices Compressor #2 .................................................................................. 11

FIGURE 10 

- Multi-Unit Sequence .......................................................................................................................... 11

FIGURE 11 

- Condenser Flow Sensors................................................................................................................... 11

FIGURE 12 

- Paddle/DP Type Flow Sensor ............................................................................................................12

FIGURE 13 

-  Electro-Mechanical Starter Manual Reset Overloads  

(2300 To 4160 Volts U.l. Or C.S.A. Approved Units Only) .................................................................12

FIGURE 14 

-  Electro-Mechanical Starter Manual Reset Overloads  

(2300 To 4160 Volts U.l. Or C.S.A. Approved Units Only) .................................................................13

FIGURE 15 

- Remote Current Limit Setpoint with 0-10VDC Or 2-10VDC Signal ...................................................13

FIGURE 16 

- Remote Current Limit Setpoint with 0-20mA Or 4-20mA Signal ........................................................14

FIGURE 17 

- Remote Current Limit Setpoint with PWM Signal ..............................................................................14

FIGURE 18 

- Remote Current Limit Setpoint with 0-1VDC or 2-10VDC Signal ......................................................15

FIGURE 19 

- Remote Leaving Chilled Liquid Temperature Setpoint with 0-20mA Or 4-20mA Signal ....................16

FIGURE 20 

- Remote Leaving Chilled Liquid Temperature Setpoint with PWM Signal ..........................................17

FIGURE 21 

- External Signal for Refrigeration Unit Failure (Note 6) ......................................................................17

FIGURE 22 

- Auxiliary Safety Shutdown Input ........................................................................................................17

FIGURE 23 

- Evaporator Flow Sensors ..................................................................................................................18

FIGURE 24 

- Paddle/DP Type Flow Sensor ............................................................................................................18

Содержание YD





















Отзывы: