background image

P5417052 

i

Important Notice

 

Johnson Controls Inc. pursues a policy of continuing improvement in design and performance in its 

products. As such, Johnson Controls Inc. reserves the right to make changes at any time without 

prior notice.

 

Johnson Controls Inc. cannot anticipate every possible circumstance that might involve a potential hazard.

 

This heat pump air conditioning unit is designed for standard air conditioning applications only. Do 

not use this unit for anything other than the purposes for which it was intended for.

 

● The installer and system specialist shall safeguard against leakage in accordance with local pipefitter 

and electrical codes. The following standards may be applicable, if local regulations are not available. 

International Organization for Standardization: (ISO 5149 or European Standard, EN 378). No part 

of this manual may be reproduced in any way without the expressed written consent of Johnson 

Controls Inc.

 

This heat pump air conditioning unit will be operated and serviced in the United States of America 

and comes with a full complement of the appropriate Safety, Danger, and Caution, Warnings.

 

If you have questions, please contact your distributor or contractor.

 

This manual provides common descriptions, basic and advanced information to maintain and service 

this heat pump air conditioning unit which you operate as well for other models.

 

● This heat pump air conditioning unit has been designed for a specific temperature range. For optimum 

performance and long life, operate this unit within the range limits according to the table below.

 

This manual should be considered as a permanent part of the air conditioning equipment and should 

remain with the air conditioning equipment.

Product Inspection upon Arrival

1.  Upon receiving this product, inspect it for any damages incurred in transit. Claims for damage, either 

apparent or concealed, should be filed immediately with the shipping company.

2.  Check the model number, electrical characteristics (power supply, voltage, and frequency rating), and 

any accessories to determine if they agree with the purchase order.

3.  The standard utilization for this unit is explained in these instructions. Use of this equipment for 

purposes other than what it designed for is not recommended. 

4.  Please contact your local agent or contractor as any issues involving installation, performance, or 

maintenance arise. Liability does not cover defects originating from unauthorized modifications 

performed by a customer without the written consent of Johnson Controls, Inc. Performing any 

mechanical alterations on this product without the consent of the manufacturer will render your 

warranty null and void.

Temperature

Maximum

Minimum

Cooling

Operation

Indoor

89

o

F DB/73

o

F WB (32

o

C DB/23

o

C WB)

69

o

F DB/59

o

F WB (21

o

C DB/15

o

C WB)

Outdoor

118

o

F DB (48

o

C DB) *

14

o

F DB (-10

o

C DB) *

Heating

Operation

Indoor

 80

o

F DB (27

o

C DB)

59

o

F DB ( 15

o

C DB)

Outdoor

59

o

F WB (15

o

C WB) *

-4

o

F WB (-20

o

C WB) *

DB: Dry Bulb, WB: Wet Bulb
* The temperature may change depending on the outdoor unit.

Содержание TIWM006B21S





















































Отзывы: