manualshive.com logo in svg

York MILLENNIUM YK, Эксплуатация и техническое обслуживание, Страница: 42 / 60

Поделиться
Скачать
York MILLENNIUM YK Скачать руководство пользователя страница 42

42

YORK INTERNATIONAL

tion of Service manual, Form 160.49-M2.

While the chiller is shut down, the orifice will be in the

fully open position causing the sensed level to be ap-

proximately 0%. When the chiller is started, after the

vane motor end switch (VMS) opens when entering

“SYSTEM RUN”, if actual level is less than the level

setpoint, a linearly increasing ramp is applied to the

level setpoint. This ramp causes the setpoint to go from

the initial refrigerant level (approximately 0%) to the

programmed setpoint over a period of 15 minutes. While

this ramp is in effect,

  

   PULLDN  LEVEL = XXX%;  SETP = XXX%;   ACTUAL = XXX% 

      

is

one of the scrolled messages under the 

DISPLAY DATA

key. “PULLDN LEVEL” is the ramping setpoint that will

ramp up to the programmed setpoint “SETP”.  “SETP”

is the level setpoint programmed by the service techni-

cian. “ACTUAL” is the present refrigerant level in the

condenser. After the 15 minute pulldown period has

elapsed, this message is replaced by
  

 

ACTUAL  LEVEL = XXX%;   LEVEL  SETP = XXX%  

   

.

If the actual level is greater than the setpoint when the

VMS opens, there is no pulldown period, it immediately

begins to control to the programmed setpoint.

While the chiller is running, the refrigerant level is nor-

mally controlled to the level setpoint. However, any-

time the vanes fully close (VMS closes), normal level

control is terminated, any refrigerant level setpoint

pulldown in effect is cancelled and the outputs to the

level control will be opposite that which is supplied to

the vane motor (i.e., when a close pulse is applied to

the vane motor, an open pulse is applied to the level

control, etc.). When the VMS opens, if the refrigerant

level is less than the level setpoint, a refrigerant level

setpoint pulldown is initiated as described above. Oth-

erwise, the level is controlled to the programmed set-

point.

If the refrigerant level sensor output ever goes to greater

than 4.4VDC, indicating a level greater than 100%,
 

  

WARNING-REFRIGERANT  LEVEL  OUT  OF  RANGE  

    

is dis-

played and the level control actuator is driven open

until the level has decreased to a level within range.

When within range, the warning message is automati-

cally cleared and normal control is resumed.

OPTIONAL SERVICE ISOLATION VALVES

If your chiller is equipped with optional service isola-

tion valves on the discharge and liquid line, these valves

must remain open during operation. These valves are

used for isolating the refrigerant charge in either the

evaporator or condenser to allow service access to the

system. A refrigerant pump-out unit will be required to

isolate the refrigerant.

CAUTION: Isolation of the refrigerant in this sytem

must be performed by a qualified service

technician.

OPTIONAL HOT GAS BYPASS

Hot gas bypass is optional and is used to eliminate

compressor surge during light load or high head op-

eration. The hot gas control panel will automatically

modulate the hot gas valve open and closed as re-

quired. Adjustment of the hot gas control valve must

be performed by a qualified service technician follow-

ing the Hot Gas Set-up procedure.

NOTE: Changes in chilled water flow will require re-

adjsutment of the hot gas control to insure

proper operation.

MICROCOMPUTER CONTROL CENTER
(See Section 2)

The MicroComputer Control Center is factory mounted,

wired and tested. The electronic panel automatically

controls the operation of the unit in meeting system

cooling requirements while minimizing energy usage.

For detailed information on the Control Center, refer to

“Section 2” of this manual.

SOLID STATE STARTER (Optional)

The Solid State Starter is a reduced voltage starter that

controls and maintains a constant current flow to the

motor during start-up. It is mounted on the chiller. Power

and control wiring between the starter and chiller are

factory installed. Available for 380-600 volts, the starter

enclosure is NEMA-1 with a hinged access door with

lock and key. Electrical lugs for incoming power wiring

are provided.

VARIABLE SPEED DRIVE (Optional)

A 460V – 3-Ph – 60/50Hz Variable Speed Drive can be

factory packaged with the chiller. It is designed to vary

the compressor motor speed and prerotation vane po-

sition by controlling the frequency and voltage of the

electrical power to the motor. Operational information

is contained in Form 160.00-O1. The control logic au-

tomatically adjusts motor speed and compressor

prerotation vane position for maximum part load effi-

ciency by analyzing information fed to it by sensors

located throughout the chiller.

Содержание MILLENNIUM YK





























































Отзывы:

Нет отзывов