manualshive.com logo in svg

York MILLENNIUM YK, Эксплуатация и техническое обслуживание, Страница: 25 / 60

Поделиться
Скачать
York MILLENNIUM YK Скачать руководство пользователя страница 25

FORM 160.52-O1

25

YORK INTERNATIONAL

   SYSTEM  READY  TO  START

Indicates that the system is not running, but will start

upon application of a start signal.

   STANDBY LUBE IN PROCESS - XXX.X MIN LEFT

Displayed while the chiller is idle and the oil pump is

running during the standby lubrication cycle. The

standby lubrication cycle will run the oil pump for 2 min-

utes every 24 continuous hours of idle time. This fea-

ture provides oil to the bearings and shaft seal during

prolonged shutdowns.

   SYSTEM  SHUTDOWN – PRESS  STATUS

Displayed when chiller is shut down on a cycling shut-

down, safety shutdown (operator must move the 

COM-

PRESSOR 

switch to 

STOP/RESET 

in order to restart)

or operator-initiated shutdown (within 30 minutes of

initial start-up). The status message consists of the day

and time of shutdown, cause of shutdown, and type of

restart required. Upon pressing 

 STATUS 

key, System

Shutdown Message will be displayed for 2 seconds and

then return to

    SYSTEM  SHUTDOWN – PRESS  STATUS

Display can be held indefinitely by depressing 

DISPLAY

key. For examples of System Shutdown Messages, see

below.

SYSTEM SHUTDOWN MESSAGES

Day of Week

Cause of Shutdown

Time of Day

       Type of Restart

   MON   10:00 AM  –  LOW   WATER   TEMP  –  AUTOSTART

Chiller was shut down on Monday at 10:00 AM because

the LCWT has decreased to a value that is 4°F (2.2°C)

below the operator-programmed chilled liquid tempera-

ture setpoint. However, if the setpoint is less than 40°F

(4.4°C), the chiller will always shut down at 36°F (2.2°C).

Further, if the chiller is running and the setpoint is

changed, the (Low Water Temperature) cutout will be

36°F (2.2°C) for 10 minutes in order to eliminate nui-

sance trips. Finally, for brine chilling applications, the

LWT cutout is always 4°F (2.2°C) below the setpoint.

(The water jumper on the Micro Board must be removed

for a brine unit.)

    MON  XX:XX AM  – FLOW SWITCH  –  AUTOSTART

Chiller is shut down because a chilled-liquid flow switch

has opened. The flow switch must open for a minimum

of 2 seconds in order to cause a shutdown. The flow

switch is checked 25 seconds into “Start Sequence

Initiated” and continuously thereafter.

    MON  XX:XX AM  –  SYSTEM CYCLING  –  AUTOSTART

A remote command (computer relay contact or manual

switch) connected to the Remote/Local cycling input of

the digital input board has shut down the chiller.

    MON  XX:XX AM  –  MULTI  UNIT  CYCLING  –  AUTOSTART

Lead/Lag sequence control accessory has shut down

the chiller.

    MON  XX:XX AM  –  POWER FAILURE  –  AUTOSTART

The chiller is shut down because there has been a

power interruption or failure. The chiller will automati-

cally restart when power is restored. This message will

be displayed if the Micro Board is configured for 

AUTO-

RESTART AFTER POWER FAILURE

. The Micro

Board is factory set for manual restart after power fail-

ure. To convert it to auto-restart after power failure, re-

move one of the two-pin program jumpers from the cloth

bag located inside the Control Center and place it on

the terminals labeled “Auto R” (J60) on the Micro Board.

    MON  XX:XX AM  –  POWER  FAILURE

The chiller is shut down because there has been a

power interruption or failure. When power is restored,

pressing the COMPRESSOR switch to STOP/RESET

position and then to START position can restart the

chiller. This message will be displayed if the Micro Board

is configured for 

MANUAL RESTART AFTER POWER

FAILURE

. The Micro Board is factory set for manual

restart after power failure. This has been accomplished

by removing the two-pin jumper from the terminals la-

beled “Auto R” (J60) on the Micro Board.

    AC  UNDERVOLTAGE  –  AUTOSTART

The chiller is shut down because the MicroComputer

Control Center was in 

RUN 

mode, displaying

   SYSTEM  RUN  –  LEAVING TEMP CONTROL

but the motor current was less than 10% FLA for 25

continuous seconds. This is indicative of an AC

undervoltage condition that has caused the start relay

(1R) in the MicroComputer Control Center to de-ener-

gize. This condition is checked when the MicroCom-

puter Control Center goes into 

RUN 

mode (after 30

second pre-lube). This condition can be caused by fail-

ure of any component that would cause a loss of the

start signal from the Control Center. In essence, this

check assures that the compressor is running when

the Control Center is displaying

Содержание MILLENNIUM YK





























































Отзывы:

Нет отзывов