York MaxE YK Series Скачать руководство пользователя страница 25

Страница: 25 / 36

YORK INTERNATIONAL

FORM 160.54-O2(1102)

YORK INTERNATIONAL

SECTION 6

MAINTENANCE

RENEWAL PARTS

For any required Renewal Parts, refer to YORK Re-

newal Parts Unit Components Manual 160.73-RP1.

CHECKING SYSTEM FOR LEAKS

Leak Testing During Operation

The refrigerant side of the system is carefully pressure

tested and evacuated at the factory.

After the system has been charged, the system should

be carefully leak tested with a R-134a compatible leak

detector to be sure all joints are tight.

If any leaks are indicated, they must be repaired im-

mediately. Usually, leaks can be stopped by tighten-

ing flare nuts or flange bolts. However, for any major

repair, the refrigerant charge must be removed. (See

“Handling Refrigerant for Dismantling and Repair”,

page 29.)

CONDUCTING R-22 PRESSURE TEST

With the R-134a charge removed and all known leaks

repaired, the system should be charged with a small

amount of R-22 mixed with dry nitrogen so that a

halide torch or electronic leak detector can be used to

detect any leaks too small to be found by the soap test.

To test with R-22, proceed as follows:

1. With no pressure in the system, charge R-22 gas

into the system through the charging valve to a

pressure of 2 PSIG (14 kPa).

2. Build up the system pressure with dry nitrogen to

approximately 75 to 100 PSIG (517 to 690 kPa).

To be sure that the concentration of refrigerant has

reached all part of the system, slightly open the oil

charging valve and test for the presence of refrig-

erant with a leak detector.

3. Test around each joint and factory weld. It is

important that this test be thoroughly and carefully

done, spending as much time as necessary and us-

ing a good leak detector.

4. To check for refrigerant leaks in the evaporator and

condenser, open the vents in the evaporator and

condenser heads and test for the presence of refrig-

erant. If no refrigerant is present, the tubes and tube

sheets may be considered tight. If refrigerant is de-

tected at the vents, the heads must be removed, the

leak located (by means of soap test or leak detector)

and repaired.

EVACUATION AND DEHYDRATION OF UNIT

FIG. 11 –

EVACUATION OF CHILLER

27385A(D)

LD00949

Содержание MaxE YK Series





































Результаты поиска

Содержание MaxE YK Series

Отзывы:

Похожие инструкции для MaxE YK Series

Бренды по названию

Популярные бренды

York MaxE YK Series, Эксплуатация и техническое обслуживание

Результаты поиска

Содержание MaxE YK Series

Отзывы:

Похожие инструкции для MaxE YK Series

Бренды по названию

Популярные бренды