background image

6

IM 12F05B10-01EN 2nd Edition : June 01, 2021-00

n

  Safety, Protection, and Modification of the Product

•  In order to protect the system controlled by the product and the product itself and ensure 

safe operation, observe the safety precautions described in this user’s manual. We assume 

no liability for safety if users fail to observe these instructions when operating the product.

•  If this instrument is used in a manner not specified in this user’s manual, the protection 

provided by this instrument may be impaired.

•  If any protection or safety circuit is required for the system controlled by the product or for 

the product itself, prepare it separately.

•  Be sure to use the spare parts approved by Yokogawa Electric Corporation (hereafter 

simply referred to as YOKOGAWA) when replacing parts or consumables.

•  Modification of the product is strictly prohibited.

•  The following safety symbols are used on the product as well as in this manual.

 WARNING

This symbol indicates that an operator must follow the instructions laid out in this manual in order 

to avoid the risks, for the human body, of injury, electric shock, or fatalities. The manual describes 

what special care the operator must take to avoid such risks.

 CAUTION

This symbol indicates that the operator must refer to the instructions in this manual in order to 

prevent the instrument (hardware) or software from being damaged, or a system failure from 

occurring.

CAUTION

This symbol gives information essential for understanding the operations and functions.

NOTE

This symbol indicates information that complements the present topic.

This symbol indicates Protective Ground Terminal.

n

  Warning and Disclaimer

The product is provided on an “as is” basis. YOKOGAWA shall have neither liability nor 

responsibility to any person or entity with respect to any direct or indirect loss or damage arising 

from using the product or any defect of the product that YOKOGAWA can not predict in advance.

Содержание FC800D

















Отзывы: