28
IM AQ6370D-02EN
Item
Specifications
Safety standards
Conforming standards
EN 61010-1
EN
60825-1
Pollution
degree
2
14
Emissions
Conforming standards
EN 61326-1
Class A
EN 55011
Class A, Group 1
EN
61000-3-2
EN
61000-3-3
RCM EN 55011 Class A, Group 1
Korea Electromagnetic Conformity Standard
(
한국 전자파적합성기준
)
This is a class A instrument (industrial use). Wireless interference
may occur in home environments. If so, the user must take
appropriate countermeasures.
Cable conditions
• TRIGGER IN, TRIGGER OUT, ANALOG OUT terminal.
Use a BNC cable
15
• Use a serial (RS-232) interface connectorand RS-232 shielded
cable.
15
• Use an Ethernet connector and a category 5 or higher Ethernet
cable.
16
• Use a VIDEO OUT connector and a D-sub 15pin VGA shielded
cable
15
• Use a USB peripheral (such as a mouse) that uses a USB port
and shielded cable
15
• Use the GP-IB interface connector and a GP-IB shielded
cable
15
Immunity
Conforming standards
EN 61326-1 Table 2 (For use in industrial locations)
Effect in immunity environment
Wavelength measurement sensitivity:
Within ±0.1 nm
Cable conditions
Same as above emission cable conditions.
Environmental standard
Compliant standards
EN 50581
Monitoring and control instruments including industrial monitoring
and control instruments.
1: Horizontal axis scale: In wavelength display mode
2: 9.5/125 µm single mode fiber (PC polishing), after warm-up of 1 hours, after alignment with a built-in wavelength reference
light source or single longitudinal mode laser (wavelength: 1520 to 1560 nm, peak level: –20 dBm or higher, level stability: 0.1
dBpp or less, wavelength stability: ±0.01 nm or less)
3: Vertical scale: absolute value level display mode, resolution setting: 0.05 nm or more, resolution correction: OFF
4: When using 9.5/125 µm single mode fiber (SSMA type in JIS C6835, PC polishing, mode field diameter: 9.5 µm, NA: 0.104 to
0.107)
5: After wavelength calibration using a built-in wavelength reference light source or single longitudinal mode laser (peak level:
–20 dBm or higher, absolute waveform accuracy in the wavelength range of 1520 to 1560 nm ± 0.003 nm or less)
6: With the resolution setting of 0.05 nm, at ambient temperature of 23 ±3 °C.
7: High dynamic mode: OFF, pulse light measurement mode: OFF, resolution correction: OFF
8: 1523 nm, high dynamic mode:SWITCH, resolution correction: OFF
9: Span 100 nm or less, wavelength sampling points: 1001, averaging times: 1
10: When applying a HeNe laser (1523 nm), resolution: 0.1 nm, 1520 nm to 1620 nm (excluding peak wavelength ± 2 nm).
11: When using the Yokogawa signal mode fiber with our standard Angled PC connector, it is 15 dB(Typ.) when using the PC
connector.
12: Certain commands may not support the AQ6317 depending on the relationship between the target model specifications and
functions.
13: The LDC display may contain defective pixels (always ON or always OFF).
(0.002% or fewer of all pixels including RGB). Does not indicate a general malfunction.
14: Pollution degree refers to the degree of adherence by a solid, liquid, or vapor that reduces the withstand voltage or surface
resistance factor. Pollution degree 1 applies to closed atmospheres (no pollution, or only dry, non-conductive pollution).
Pollution degree 2 applies to normal indoor atmospheres (with only non-conductive pollution).
15: Use a cable of 3 m in length or less.
16: Use a cable of 30 m in length or less.
*: Typical values(typ.) are typical or mean values. They are not strictly guaranteed.
11 Specifications
