Yeastar Technology TG400G Скачать руководство пользователя

Страница: 86 / 104

TG Series User Guide

86/104

Configure QoS Settings

QoS (Quality of Service) is a major issue in VoIP implementations. You can configure QoS settings

to guarantee that packet traffic for a voice or other media connection will not be delayed or dropped

due interference from other lower priority traffic.

Navigate to

Gateway > VoIP Settings > SIP Settings > QoS

to configure the QoS settings.

Note: we recommend that you configure the QoS in your router or switch instead of TG gateway.

Configure Respond Code Settings

You can change the respond codes from the SIM card carrier before sending the codes to your PBX.
After changing the respond codes, the PBX can better understand the exact call status, like busy, no
response and others.

Navigate to

Gateway > VoIP Settings > SIP Settings > Respond Code

to configure the respond

code settings.

Note: if you are not familiar with the respond codes, contact the PBX administrator and SIM card
carrier before you change the settings.

Содержание TG400G









































































































Результаты поиска

Содержание TG400G

Отзывы:

Похожие инструкции для TG400G

Бренды по названию

Популярные бренды

Yeastar Technology TG400G, Руководство пользователя

Результаты поиска

Содержание TG400G

Отзывы:

Похожие инструкции для TG400G

Бренды по названию

Популярные бренды