Yeastar Technology TG400G Скачать руководство пользователя

Страница: 7 / 104

TG Series User Guide

7/104

About This Guide

Thanks for choosing Yeastar TG Series GSM/3G/4G gateway.

This guide will help you learn how to operate and manage your TG gateway. In this guide, we
describe every detail on the functionality and configuration of the TG series gateway.

We begin by

assuming that you are interested in TG series gateway and familiar with networking and other IT
disciplines.

Products Covered

This guide explains how to configure the following Yeastar TG series gateways:



TG200



TG400



TG800



TG1600

Safety When Working with Electricity



Do not use a 3

party power adaptor.



Do not power on the device during the installation.



Do not work on the device, connect or disconnect cables when lightning strikes.

Содержание TG400G









































































































Результаты поиска

Содержание TG400G

Отзывы:

Похожие инструкции для TG400G

Бренды по названию

Популярные бренды

Yeastar Technology TG400G, Руководство пользователя

Результаты поиска

Содержание TG400G

Отзывы:

Похожие инструкции для TG400G

Бренды по названию

Популярные бренды