Yazoo/Kees ZELKH6125 страница 49 Скачать руководство пользователя | Manualshive

Страница: 49 / 68

background image

lUbRICaTION

49

Wheel and Deck Zerks

Use only good quality bearing grease.
Grease from well-known brand names (petrochemical
companies, etc.) usually maintains a good quality.

Front Wheel Mount

Lubricate with a grease gun until the grease is forced
out around the top washer.

Front Wheel Bearings

Lubricate 3-4 strokes with a grease gun on each set of
wheel bearings.

8065-032

Lubricating front wheels

8065-064

Deck spindle

Deck Spindles

Lower the cutting deck completely.
If a grease gun without rubber hose is used, the foot
plate must be removed.
Lubricate with a grease gun, 2-3 strokes per spindle.

IMPORTANT INFORMATION
Use minimal lubrication and remove excess
lubricant so that is does not come into contact
with belts or belt pulley drive surfaces.

«
...
47
48
49
50
51
...
»

Содержание ZELKH6125





































































Отзывы:

Нет отзывов

Похожие инструкции для ZELKH6125

Бренд: Baroness Страницы: 5

Бренд: Kärcher Страницы: 32

Бренд: Ransomes Страницы: 36

Бренд: Tanaka Страницы: 8

Бренд: Dixon Страницы: 8

Бренд: McCulloch Страницы: 10

Бренд: Jacobsen Страницы: 20

Бренд: MTD Страницы: 20

Бренд: MTD Страницы: 36

Бренд: Ariens Страницы: 26

Бренд: Yard Machines Страницы: 27

Бренд: Honda Страницы: 24

Бренд: Bad Boy Страницы: 36

Бренд: LawnMaster Страницы: 16

Бренд: ARNETOLI MOTOR Страницы: 2

Бренд: BEAL Страницы: 46

Бренд: AVANT Страницы: 30

Бренд: Dolmar Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды