manualshive.com logo in svg

YASKAWA GPD 506/P5, Руководство по устранению неисправностей, Страница: 37 / 67

Поделиться
Скачать
YASKAWA GPD 506/P5 Скачать руководство пользователя страница 37

PP.P5G5.03.Troubleshoot

Page 37

Rev. 06/11/2003

Fault Codes

Parameter Setting Error 

- Inverter can’t run. The fault is displayed 

on the digital operator, and the fault relay is not activated.

Multi-function input or multi-function output data 

setting error.

OPE08

Terminal

Possible Cause(s): 

A multi-function selection has been chosen that is not offered in the 

present control mode.

Corrective Action: 

Check the “modified constants” area and verify the set values in

parameters H1-01~H1-06, H2-01~H2-03,  H3-05, H3-09, H4-01 and H4-04.

V/F data setting fault. 506 digital operator will display 

OPE10.

OPE10

V/F Ptrn Setting

Possible Cause(s): 

The V/f parameter settings are not set correctly.

Corrective Action: 

Check parameters (E1-04 ~ E1-11) for the 515/G5 and parameters 

(n012 ~ n018) for the 506/P5. A minimum frequency/voltage value may be set higher than the 
maximum frequency/voltage.

ope 5

N/A

505

506 

515 

√

505

506 

√

    

515 

√

Содержание GPD 506/P5




































































Отзывы:

Нет отзывов